The best mowing pattern is one that allows the clippings to discharge towards the uncut part of the lawn. This permits recutting of the clippings to further pulverize them. When cutting high weeds, discharge towards cut portion, then recut at right angles to first direction. Lawn should be cut in the fall as long as there is growth. 6 NOTE The manufacturer DOES NOT recommend the use of any accessory on this rotary mower other than those manufactured by MTD Products Inc. GRASS CATCHER Model

Disconnect the spark plug wire, and keep the wire away from the plug to prevent accidental starting. 8. Do not run the engine indoors. 9. Shut the engine (motor) off and wait until the blade comes to a complete stop before removing the grass catcher or unclogging chute. 10. Mow across the face of slopes, never up-and-down. Exercise extreme caution when changing direction on slopes. Do not mow excessively steep slopes. 11. Always disconnect electric mowers (line operated) before cleaning, rep

Inside Rear Cover IMPORTANT All references to LEFT and RIGHT sides of the tiller are given from the operator’s position behind the handlebars (unless specified otherwise). Dear Owner: Congratulations! You now own one of the finest rear-tine tillers available. The TROY-BILT® TUFFY®, along with the other TROY-BILT tiller models in the lineup, make up the finest family of tillers available to gardeners today. Your new TUFFY® tiller, because of its rugged build, ease of operation, and maneuvera

Keep these ideas in mind when you plan your garden. You can design the layout of the garden so that you’ll get the most beneficial use from your tiller. Guiding Your Tiller When tilling, relax and allow the tiller to move along at its own speed. Don’t try to push it along to make it go faster. Do not try to push down on the handlebars in an attempt to make the tiller dig deeper. Walk to the side of the tiller that is yet to be tilled. Use one hand and keep a firm hand grip on the handlebars (

Please remember that your local dealer will need to know the identification numbers of your machine to give you the most efficient service. Please see below for how to identify and record the identification numbers for your machine. When ordering parts, please be sure to provide the following information: 1. The SERIAL NUMBER of your machine. 2. The PART NUMBER of the part. 3. The PART DESCRIPTION. 4. The QUANTITY needed. If you need engine service or parts: For engine service or parts, p

1 45 1224-4 Shim-as above, .062"...............As Req' 16A 2566 Cover-power unit transmission (incl.Ref. No.’s 18,19, 20, 21, 22, 23 and 24)................................. 1 46 1714 Bearing & Cup-tapered cone roller bearing with cup (race). Cone and cup sold as set only................... 2 17 1123 Gasket-transmisslon cover........... 1 47 11601 Shaft-main drive, power unit. Incl. 18 90008 Bolt-hex hd., 5/16-18x1", Grade 5, (remove with care)................... 1 Integral worm, plus two

For storing the tine attachment when removed from power unit. Also 1 2195 Leg-kickstand............................. 1 assists in removal and replacement 2 2196 Plate-kickstand mounting........... 1 of tine attachment.................... 1 3 1492 Spring-kickstand......................... 1 13 2299 Rear Cradle Support.................... 1 4 9336 Pin—clevis.................................... 1 14 2301 Front Cradle Support................... 1 5 9741 Bolt-hex hd., 5/16-18x2", 15 2297 T

2 Bolt-hex hd„ 3/8-16x2"............. 4 Locknut-3/8"-16.......................... 4 This Ref. No. not used................. This Ref. No. not used................. Bolo Tine-single, left hand. Used on left and right side tine assy. Tine is stamped either “EL" or “AL". (Incl. two each of Ref. No.’s 8, 9 and 10)............................. 8 Bolo Tine-single, right hand. Used on left and right side tine assy. Tine is stamped either “ER" or “AR”. (Incl. same hardware as Ref. No. 6)......

New York 12180 Mon.-Fri.: 8 a.m. to 7:00 p.m. Sat. 9 a.m. to 4 p.m. For Parts Sales: 1-800-648-6776 For Technical Scrvice: 1-800-833-6990 In Canada: Garden Way Incorporated 320 Van Sickle Road, Unit 12 St. Catherines, Ontario L2R 6P7 Mon.-Fri.: 8 a.m. to 5:00 p.m. For Parts Sales or Technical Servicc: 1-800-225-3585 ^ CAUTION We urge that you use only genuine TROY-BILT® replacement parts, which meet all of the latest requirements. Replacement parts manufactured by others could present safety

Failure to tighten or replace fasteners can cause poor performance, equipment damage or oil leakage. See your Parts Catalog for complete fastener descriptions. Most hardware on your tiller is visible. Pay particular attention to hardware shown in Photos 5-1,5-2, 5-3, and Figure 5-3A. 1. Check the transmission pulley mounting bolt (Photo 5-1). If the washer behind the bolt head is loose, the bolt needs tightening. To do this, first insert a punch or thick screwdriver into the hole next to the