If you are installing your spa with any type of structure on the outside, such as a gazebo, remember to allow access for service. It is always best to design special installations so that the spa can still be accessed. Outdoor equipment pack (in-ground spas only) The Designer Spa series requires an external equipment pack. When locating the outdoor equipment pack, you will want to consider the following: The equipment pack must be located within a maximum of 15 feet • from the spa. Ensure the eq

All rights reserved. Duplication without written consent is strictly prohibited. Cal Spas® is a registered trademark. Due to continuous improvement programs, all models, operation, and/or specifications are subject to change without prior notice. LTR20091024, Rev. A 12/15/08 CONTACT INFORMATION For customer service, please contact your authorized dealer immediately. If you need additional information and/or assistance, please contact: LMS Customer Service Department 1462 East Ninth Street Pomona

The sand bed is to level the spa shell and provide a perfect support base with no voids when the spa is lowered into the hole. Your excavation should be approximately one foot longer and one foot wider than the spa shell. This will allow for a six inch over dig all the way around the spa once it is in place. Additional hand excavation will be required to insure the skimmer will fit in the excavation when attached to the spa. Sand or rock dust must be used to bed the shell into the excavation and

To test the GFCI breaker follow these instructions (spa should be operating): Press the TEST button on the GFCI. The GFCI will trip and the spa will 1. shut off. Reset the GFCI breaker by switching the breaker to the full OFF posi2. tion, wait a moment, then turn the breaker back on. The spa should have power again. Configuring the 6300 Control System The 6300 control system requires higher power than other 240V systems. Dip switch #10 is factory set in the ON position. This causes the heater to

Designer Spa Specifications DIJ401 and DIJ405: Equipment pack weight = 250 lbs. DIJ407: Equipment pack weight = 300 lbs. 2.5 HP heat pump 4 HP swim pump Note: Equipment pack cannot exceed 15 feet from spa. In-Ground Plumbing Connections IMPORTANT! Always check local codes prior to any in-ground spa installation. Once the spa and equipment are properly located, you will want to lay out the plumbing run. Trenches should be deep and wide enough to allow all pipes to be buried below the frost line a

Topside Control Panel and Temp Sensor: 1” line that connects to the bottom of the control box located on the equipment pack. Electrical and Electronic Connection Remote Equipment Topside Control Panel The next few steps to complete the installation should be performed along with installation of the temperature sensor and 12V spa light wiring (if applicable). All of these components are generally installed using the same conduit. Locate the topside control panel 1. extension loom in the control b

If you are pouring a regular deck up to the spas coping, then the top of the coping should be 4” above the surrounding area. In either event, it is recommended to dig out an area around the spa exposing the flange of the coping and just under it. This is important, as concrete should be packed under and over the flange of the spa, as the deck is poured. This will lock the spa into the concrete and provide for a much stronger bond of the spa to the deck. It will also eliminate cracking of the dec

C om REJUVINATE YOUR MIND & BODY IN COMFORT 221 WWW . CA l S p AS . C om REJUVINATE YOUR MIND & BODY IN COMFORT 221 As the leader in Home Resort products, Cal Spas is committed to providing complete backyard solutions. This tradition continues with Cal Heat’s selection of stylish and affordable saunas. Cal Heat is the leader in innovative Sauna designs and has modernized this age-old Finnish therapy to meet your Home Resort needs. With a Cal Heat Sauna, you can enjoy the proven health benefits o

While steam saunas regularly reach temperatures from 140° to 190°, infrared saunas provide many of the same health benefits of traditional steam saunas but only raise the indoor temperature from 105° to 140°. The benefits of an infrared sauna are felt quickly due to the relatively short amount of time needed to preheat. Carbon fiber Carbon Fiber heating (found on our Carbon Fiber Series) operates similarly to infrared heating. In a Carbon Fiber sauna, the wavelength is optimized to more deeply d

Available in both straight and corner configurations with seating for 1 to 4 adults, there is an Infrared model for every indoor configuration. Usage: Heating Type: Configurations: Seats: Usage: Heating Type: Configurations: Seats: Usage: Heating Type: Configurations: Seats: Usage: Heating Type: Configurations: Seats: Outdoor Steam In-Line Up to 5 Indoor Steam In-Line & Corner Up to 4 Indoor Carbon Fiber In-Line & Corner Up to 4 Indoor Infrared In-Line & Corner Up to 4 WWW . CA l S p AS . C om 2