WARNING ! This manual must be read and understood before adjustment, service, or maintenance is performed. Modification of this product can result in property damage. Dometic Corporation • SeaLand 13128 State Rt. 226, P.O. Box 38 Big Prairie, OH 44611-0038 USA SeaLand Product Hotline 1-800-321-9886 (8:00 a.m. -5:00 p.m. ET) TABLE OF CONTENTS Page Product Features . . . . . . . . . . . . . . . . . . . . .2 Key System Components . . . . . . . . . . . . . . .3 Toilet Model Identification . . . . .

For the name of a dealer near you, please call our toll free number 1-800-321-9886 or fax us at 330-496-3097 from 8:00 a.m. to 5:00 p.m. (eastern time) monday through Friday. You may also write us at: Dometic Corporation, po box 38, big prairie, oH 446 usa. 0 iMportant inforMation Why do i need to use a holding tank deodorant? all types of marine or rV systems offer ideal conditions for odor to grow out of control. when closed, the mechanical seals in the toilets described earlier also act as an

see Figure . 4. use pencil or awl to mark location of hold down bracket mounting holes. 5. remove sanipottie® portable toilet. Figure 6. Attach hold down brackets to the floor or deck with screws provided. 7. set sanipottie® portable toilet between brackets and latch in place with side clasps. “MsD” perManent installation portable toilets are legally acceptable for use in vessels not having permanently installed toilets, as determined by the united states Coast Guard. However, some states and th

adapter 1 inch/25 mm Hose runs Max. horizontal run 98 ft./30 m Max. vertical run 9.8 ft./3 m Electrical System Amp draw (avg.) 12 volts DC 10-13 amps 24 volts DC 5-7 amps Circuit breaker 12 volts DC 15 amps* 24 volts DC 10 amps* * at 3.28 ft. (1 m) of pump discharge head Dometic Sanitation Corporation 3 28 State Rt. 226, P.O. Box 38, Big Prairie, OH 446 USA SeaLand Product Hotline -800-32 -9886 (8-5 ET) TAbLE OF COnTEnTS MasterFlush Technology Features .............. Installation Specifications

4. Flush the toilet without water. Repeat three times. (This procedure will minimize any remaining water in the macerator pump.) 5. Turn off power to the toilet (and water supply pump if flushing with sea water). 6. Close all seacocks. If system will be subjected to freezing temperatures, please follow above procedure, and then winterize system as described below. winTERiZing At the end of each season, the SeaLand macerator toilet should be winterized for storage by using potable water-safe anti

Rigid PVC pipe can also be dealer. Connections can be made either through installed in runs that hold trapped sewage. The the floor or out the rear of the toilet above the marine sanitation hose most resistant to odor floor. permeation is OdorSafe Plus® hose, available from your local SeaLand product dealer. Flexible hoses that contain sewage from any marine toilet will create unpleasant odor that NOTE: Vertical loops in discharge line of toilet are additive. Total upward vertical distance must

3. Close ball and wait 2-3 minutes. 4. Open flush ball. Use brush and water to rinse away cleanser and loosened deposits. Fig. A Fig. B WINTERIZING At the end of each season, the SeaLand toilet should be winterized for storage, by either draining or using potable water-safe antifreeze in the system. To drain: 1. Thoroughly flush system with fresh water. 2. Empty holding tank. 3. Shut off water supply to toilet(s), and remove inlet waterline (Fig. C). Do not remove brass cap on bottom of valve. 4

Do not attempt installation without first contacting a SeaLand Product certified dealer orDometic Corporation. WARNING! This manual must be read and understood before adjustment, maintenance, or service is performed. Modification of this product can result in property damage. Dometic Corporation • Sanitation Systems 13128 State Rt. 226, P.O. Box 38 Big Prairie, OH 44611-0038 USA SeaLand Product Hotline 1-800-321-9886 (8:00 a.m. -5:00 p.m. ET) TABLE OF CONTENTS Page Product Features. . . . . . .

Install the flange gasket over the T-bolts (fig. 10). STEP 12: Install floor flange adapter with words “THIS SIDE UP” facing up. Tighten adapter to floor flange using four flat washers and hex nuts. Tighten in criss-cross pattern (fig. 11). STEP 13: Temporarily set the toilet in place on the floor flange (fig. 14). STEP 14: Mark the holes for the two toilet mounting bolts (fig. 15). STEP 15: Pick up toilet and set aside. Drill 3/16-inch pilot holes in the floor (fig. 16). IMPORTANT: If replacing