To turn ON : Press PLAY/PAUSE button (playback starts) To turn OFF : Press STOP button once for standby mode. Press STOP button again to turn off the power. To Remove the Disc 1. Slide the LOCK switch (5) to its original position. 2. Press the CD LID OPEN button to open the CD compartment lid. 3. Hold the edge and gently press the center pivot as illustrated, then pick up the disc. CAUTION: WAIT FOR THE DISC TO STOP SPINNING BEFORE SLIDING THE OPEN SWITCH AND OPENING THE LID. Notes on CD-R/RW Di

This plug will only fit into a matching polarized AC outlet. This is a safety feature to reduce the possibility of electric shock. If this plug will not fit in your AC outlet, you probably have an outdated non-polarized outlet. You should have your out-dated outlet changed by a qualified, licensed electrician. Do not file the wide blade on the plug, or use an adaptor to make the plug fit onto your outlet. This defeats the safety feature and could expose you to electric shock. RADIO OPERATION 1.

PLAY BUTTON 29. RECORD BUTTON 3 POWER SOURCE This AM/FM STEREO CD Cassette Recorder operates on 8 x ‘LR14’ (‘C’) batteries (not included) or from AC 120V~ 60Hz line power supply. A. BATTERY OPERATION 1. Remove the Battery Door. 2. Following the polarity diagram as shown in the battery compartment insert 8 x ‘LR14’ (‘C') batteries then replace the Battery Door. IMPORTANT : Be sure that the batteries are installed correctly. Wrong polarity may damage the unit. 3. Use only the size and type of batt

iv. If the unit is not to be used for an extended period of time, remove the batteries. Old or leaking batteries can cause damage to the unit and may void the warranty. v. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. (Follow battery manufacturer’s directions). vi. Do not dispose of batteries in fire, batteries may leak or explode. BATTERY REPLACEMENT When the output sound of this unit becomes distorted or the CD player operation appears unstable,

CAUTION • AVOID EXCESSIVE VOLUME LEVELS FOR LONG PERIODS OF TIME WHEN USING THE HEADPHONES. PROLONGED USE AT HIGH LEVELS MAY IMPAIR YOUR HEARING. • Do not use earphones while operating a motorized vehicle, as it may create a traffic hazard and is illegal in many areas. BASIC OPERATION NOTE: This unit can also play 3 inch (8cm) single CDs without an adaptor. Do not use a CD single adaptor for these smaller discs. 1. Press the CD LID OPEN button to release the CD lid. 2. Insert a disc with the lab

• Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions. • Consult with your nearest dealer if installation requires the drilling of holes or other modifications to your vehicle. • Install the unit where it does not interfere with driving and cannot injure passengers if there is a sudden or emergency stop. • If the installation angle exceeds 30. from horizontal, the unit might not give optimum performance. • This unit is not

“BAL L=R” represents an equal balance between the right and left speakers. Fader Use the button to adjust the Fader between the rear and front speakers from “10R” (full rear) to “10F” ( full front). “ FAD R=F” represents an equal balance between the front and rear speakers. Loudness Control ( LOUD) When listening to music at low volume levels, this feature will boost the bass and treble ranges to compensate for the characteristics of human hearing. Press and hold the BAND/LOUD button (21) to act

Press the DVD button to play the audio from the optional DV352 DVD player through the selected speakers. The illuminated DVD indicator will change from green to red, indicating the selection was made. An 8-Pin DIN connector and left and right audio inputs cables allow you to control the DV352 through the PADIN3. Boton de Fuente DVD Presione el boton DVD para reproducir el audio del reproductor de DVD DV352 opcional, a traves de los altavoces seleccionados. El indicador de DVD iluminado cambiara

In stop mode, press the PROG button once, the display will show "PGM 01* then change to "PGM 00" and flash,'01' means program number, '00" means track number. (Press the STOP button to cancel) EN-4 Z Press K< or>W button to select the desired track. 3. Press PROG button again to enter the track into memory, the display will show "PGM 02' then change to 'PGM 00", "02" means the program number increase one step. 4 Repeat stop 2 & 3 to program the order of more tracks up to 20 tracks can be pro