Войти:
Оценок - 4, средний балл: 4 ( )

Инструкция по эксплуатации Jensen, модель CD-36

Производитель: Jensen
Размер: 166.46 kb
Название файла: 114cd270-b8e7-4efc-833c-49d7bede6282.pdf
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


CAUTION • AVOID EXCESSIVE VOLUME LEVELS FOR LONG PERIODS OF TIME WHEN USING THE HEADPHONES. PROLONGED USE AT HIGH LEVELS MAY IMPAIR YOUR HEARING. • Do not use earphones while operating a motorized vehicle, as it may create a traffic hazard and is illegal in many areas. BASIC OPERATION NOTE: This unit can also play 3 inch (8cm) single CDs without an adaptor. Do not use a CD single adaptor for these smaller discs. 1. Press the CD LID OPEN button to release the CD lid. 2. Insert a disc with the label side facing up. 3. Close the CD Lid. A click will be heard when it locks into place. 4. Press the PLAY/PAUSE button once to start playing. 5. The display will show the total number of tracks and playing time. The player will then start playing the first track. 6. Adjust the volume by turning the Volume Control. Locating a Particular Track To skip back to the beginning of the Press once or repeatedly. current or a previous track To skip to the beginning of following Press once or repeatedly. tracks Locating a Particular Point in a Track To search back at a high speed Press & hold To search forward at a high speed Press & hold EN- 6 Turning Power On and Off To turn ON and OFF, press the following buttons after a disc is inserted into the player. To turn ON: Press PLAY/ PAUSE button (playback starts) To turn OFF : Press STOP button once for standby mode. Press STOP button again to turn off the power. Auto power- off function When the unit is stopped (Standby mode) for approximately 30 seconds, the power is automatically turned off. To Remove the Disc 1. Press the CD LID OPEN button to open the CD compartment lid. 2. Hold the edge and gently press the center pivot as illustrated, then pick up the disc. CAUTION: WAIT FOR THE DISC TO STOP SPINNING BEFORE SLIDING THE OPEN SWITCH AND OPENING THE LID. LCD DISPLAY INFORMATION When the button is pressed at initial start up • The display will show “ - - “ and then the total number of tracks and total playing time. The disc will start playing and the display will show the first track number and instant playing time. • To review the total number of tracks and total playing time of the disc, press the STOP button once. During PLAY mode • The track number and instant playing time are displayed. During PAUSE mode • When the track playback is paused, the playing time flashes. Battery Low Indicator A flashing battery indicator flashes in the display when the batteries need to be changed. EN-7 NORMAL PLAYBACK VARIOUS PLAYBACK MODES VARIOUS PLAYBACK MODES NORNAL PLAYBACK The whole disc is played and the player will stop after the last track is finished. Every time the MODE button is pressed, the corresponding mode appears in the display window, in the following sequence: REPEAT 1 In stop or playback mode press the MODE Button once. When shown on the LCD display, the current track on the disc will be repeated. REPEAT ALL In stop or playback mode press the MODE Button twice. When shown in the LCD display, all tracks on the disc will be repeated. To cancel the Repeat Function, press the MODE Button repeatedly until “ ” or “ ” disappears. INTRODUCTARY SCAN To play the first 10 seconds of each track on the disc. 1. In STOP mode press the MODE button three times, INTRO is displayed. 2. Press button to start INTRO play from track number 01. 3. If INTRO mode is selected during play, INTRO will start flashing in the display. • Press button. INTRO stops flashing and INTRO play starts from track 01. • Press to start INTRO play from next track. • Press to start INTRO play from current track. • To cancel INTRO play, press again. Playback continues on current track. EN-8 RANDOM Enables all the tracks on the disc to be played in a Random sequence. 1. In STOP mode press the MODE button four times, RANDOM Indicator, “RND”, will be displayed. 2. Press button. A track is selected at random and playback begins. 3. If RANDOM mode is selected during play, “ RND” will appear and flash in the LCD Display. 4. Press button once. “RND” stops flashing and RANDOM playback begins. 5. Press the MODE Button again to return to normal play mode. PROGRAMMED PLAY Programs can be set in either the STOP or normal play mode. 1. Press the PROG button once, PROG No. 01 appears. PROG and Track No. 00 start flashing in the display. 2. Press or to select the desired track. 3. When the desired track is displayed, press the PROG button to register. The PROG No. changes to 02. Track No. returns to 00 and flashes together with PROG. 4. Repeat steps 2 and 3 to program more tracks. Up to 20 tracks can be programmed into the memory. 5. Press to start the programmed play. 6. To erase the program, in STOP mode simply press the button. EN-9 Cleaning the Cabinet PLAYER MAINTENANCE PLAYER MAINTENANCE TROUBLESHOOTING GUIDE Should you experience difficulties in the use of this player please refer to the following chart or call 1- 800- 777- 5331 for Customer Service. Problem Points to Check Player fails to function Disc may be inserted upside...

Эта инструкция также подходит к моделям:
Плееры - CD-36 (166.46 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории