Оценок - 4, средний балл: 3.8
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
• If the input channel is paired (or if a ST IN channel is selected), the send level of the signal sent from both channels to the target MIX bus will be set to –.. • The Mix Minus operation is valid even if the destination MIX bus is paired. In this case, the PAN setting of the input channel will be reflected by the PAN settings of the paired MIX buses. K Input channel This is the source input channel (or channels). Paired input channels (or a ST IN channel) are indicated by a heart symbol displayed between them. For an input channel, you can click this symbol to enable/disable pairing. You can move the cursor to a parameter in the CH to COPY area, and then hold down the [SHIFT] key and click (or press the [SHIFT] key + [ENTER] key) to copy the value of that parameter to another channel (in the horizontal direction) or to another MIX bus (in the vertical direction), or to switch all parameters on/off. You can use this method to set the following parameters. • Mix send on/off Move the cursor to the SEND ON/OFF button of the CH to COPY area; then hold down the [SHIFT] key and click (or press the [SHIFT] key + [ENTER] key) to access the following window. To set multiple parameters at once, use the [DATA] encoder to select one of the following items, and click the OK button. ALL OFF [ALL MIX ] ALL ON [ALL MIX ] Switch the signals sent from the selected input channel to all MIX buses on or off together. ALL OFF [ALL CH ] ALL ON [ALL CH ] Switch the signals sent from all input channels to the selected MIX bus on or off together. ALL OFF [ALL CH x ALL MIX] ALL ON [ALL CH x ALL MIX] Switch the signals sent from all input channels to all MIX buses on or off together. • Mix send position Move the cursor to a PRE/POST button in the CH to COPY area; then hold down the [SHIFT] key and click (or press the [SHIFT] key + [ENTER] key) to access the following window. To set multiple parameters at once, use the [DATA] encoder to select one of the following items, and click the OK button. ALL POST [ALL MIX ] ALL PRE [ALL MIX ] Switch the send position of the signal sent from the selected input channel to all MIX buses to either post- fader or pre-fader. ALL POST [ALL CH ] ALL PRE [ALL CH ] Switch the send position of the signal sent from all input channels to the selected MIX bus to either post- fader or pre-fader. ALL POST [ALL CH x ALL MIX] ALL PRE [ALL CH x ALL MIX] Switch the send position of the signal sent from all input channels to all MIX buses to either post-fader or pre-fader. Note These “all-at-once” operations are ignored by FIXED-type MIX buses. PM5D/PM5D-RH Owner’s Manual Reference section • Mix send level Move the cursor to a SEND LEVEL knob in the CH to COPY area; then hold down the [SHIFT] key and click (or press the [SHIFT] key + [ENTER] key) to access the following window. • Mix send level Move the cursor to a SEND LEVEL knob in the CH to COPY area; then hold down the [SHIFT] key and click (or press the [SHIFT] key + [ENTER] key) to access the following window. LEVEL COPY [ALL MIX ] The value of the selected SEND LEVEL knob will be copied to the send level of the signals sent from that input channel to all MIX buses. LEVEL COPY [ALL MIX ] The value of the selected SEND LEVEL knob will be copied to the send level of the signals sent from all input channels to that MIX bus. LEVEL COPY [ALL CH x ALL MIX] The value of the selected SEND LEVEL knob will be copied to the send level of the signals sent from all input channels to all MIX buses. Note These “all-at-once” operations are ignored by FIXED-type MIX buses. • Mix pan/balance When the destination MIX bus is paired, move the cursor to a MIX PAN/BALANCE knob displayed in the CH to COPY area; then hold down the [SHIFT] key and click (or press the [SHIFT] key + [ENTER] key) to access the following window. To set multiple parameters at once, use the [DATA] encoder to select one of the following items, and click the OK button. PAN (BAL) COPY [ALL MIX ] The value of the selected MIX PAN/BALANCE knob will be copied to the pan (balance) of signals sent from that channel to all paired MIX buses. PAN (BAL) COPY [ALL MIX ] The value of the selected MIX PAN/BALANCE knob will be copied to the pan (balance) of signals sent from all channels to that MIX bus. PAN (BAL) COPY [ALL CH x ALL MIX] The value of the selected parameter will be copied to the pan (balance) of signals sent from all channels to all paired MIX buses. Note • This operation is ignored by unpaired MIX buses and FIXED-type MIX buses. • You cannot copy PAN parameters to BALANCE parameters (or vice versa). • Copying is invalid for channels whose VARI button (in the FOLLOW PAN area) is on. Information shownin the GlobalfunctionsOutputfunctionsAppendices Inputfunctions PM5D/PM5D-RH Owner’s Manual Reference section 279 PAN/ROUTING function PAN/ROUTING function MIX SEND VIEW screen point) Select one of the following two parameters to view in This screen lists the signals sent from the input channels to the grid. th...
Эта инструкция также подходит к моделям:Музыкальные инструменты - PM5D-RH (18.35 mb)