Оценок - 3, средний балл: 4.7
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Press Source button to have the monitor double-check the input signal source. If the initial screen (the login screen) appears, boot the computer in the applicable mode (the safe mode for Windows ME/XP/2000) and then change the frequency of the video card. (Refer to the Preset Timing Modes) Note: If the initial screen (the login screen) does not appear, contact the Service Center or your dealer. You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can handle properly. Adjust the maximum resolution and frequency that the monitor can handle properly. If the display exceeds SXGA or 75Hz, a "Not Optimum Mode","Recommanded Mode 1280 x 1024 60Hz" message is The screen shows strange colors or just black and white. The screen suddenly has become unbalanced. The screen is out of focus or OSD cannot be adjusted. LED is blinking but no images on the screen. There are only 16 colors shown on the screen. The screen colors have changed after There is no image on the screen. Is the power indicator on the monitor blinking at 1 second intervals? Connected using the DVI cable? Is the screen displaying only one color as if looking at the screen through a cellophane paper? Have the screen colors become strange after running a program or due to a crash between applications? Has the video card been set properly? Have you changed the video card or the driver? Have you adjusted the resolution or frequency to the monitor? displayed. If the display exceeds 85Hz, the display will work properly but the "Not Optimum Mode","Recommanded Mode 1280 x 1024 60Hz" message appears for one minute and then disappears. Please change to the recommended mode during this one-minute period. (The message is displayed again if the system is rebooted.) The monitor is in PowerSaver mode. press a key on the keyboard to activate the monitor and restore the image on the screen. If there is still no image, press the 'Source' button. Then press any key on the keyboard again to activate the monitor and restore the image on the screen. You may get a blank screen if you boot the system before you connect the DVI cable, or disconnect and then reconnect the DVI cable while the system is running as certain types of graphic cards do not send out video signals. Connect the DVI cable and then reboot the system. Check the signal cable connection.Make sure the video card is fully inserted in it's slot. Reboot the computer. Set the video card by referring to the video card manual. Adjust screen image position and size using the OSD. Adjust the resolution and frequency at the video card. (Refer to the Preset Timing Modes). The screen can be unbalanced due to the cycle of the video card signals. Readjust Position by referring to the OSD. Have you adjusted the resolution or frequency on the monitor? Is the frequency properly adjusted when checking the Display Timing on the menu? Have the Windows colors been set properly? Adjust the resolution and frequency of the video card. (Refer to the Preset Timing Modes). Adjust the frequency properly by referring to the video card manual and the Preset Timing Modes. (The maximum frequency per resolution may differ from product to product.) Windows ME/2000/XP: Set the colors properly at the Control Panel > Display > Settings. changing the video card. There is a message that reads "Unrecognized monitor, Plug & Play (VESA DDC) monitor found". MagicTune doesn't work properly. Has the video card been set properly? Have you installed the monitor driver? See the video card manual to see if the Plug & Play (VESA DDC) function can be supported. Have you changed your PC or video graphic card? Set the video card by referring to the video card manual. Install the monitor driver according to the Driver Installation Instructions. Install the monitor driver according to the Driver Installation Instructions. Download the latest program. The program can be downloaded from the Check the following items if there is trouble with the monitor. 1. Check if the power cord and the video cables are properly connected to the computer. 2. Check if the computer beeps more than 3 times when booting. (If it does, request an after-service for the main board of the computer.) 3. If you installed a new video card or if you assembled the PC, check if the installed the adapter (video) driver and the monitor driver. 4. Check if the scanning ratio of the video screen is set at 75Hz. (Do not exceed 60Hz when using the maximum resolution.) 5. If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove the Display Adapter at the "Control Panel>System>Device Administrator" and then reboot the computer to reinstall the adapter (video) driver. If problems repeatedly occur, contact an authorized service center. Q & A Question Answer How can I change the frequency? Frequency can be changed by reconfiguring the video card. Note that video card su...
Эта инструкция также подходит к моделям:Мониторы - 913N (4.87 mb)