© 2003 Campbell Hausfeld IN463600AV 12/03 Specifications PW1686 2640 1650 psi 1.6 GPM 14 Amps 120V 100°F 38 lbs. Assembly Instructions Assembly Instructions and Parts List PW1686 1. Attach detergent suction tube to hose barb on detergent tank and put cap on detergent tank (Figure 1). 2. Slide accessory storage bracket onto back of pressure washer (Figure 1). 3. Slide cord holder and lance storage collar onto side of pressure washer (Figure 1). 4. Align handle on back of pressure washer and attac

15- ENG D25804 TROUBLE SHOOTING GUIDE PROBLEM CAUSE CORRECTION Engine will not start (see Engine Manual for further engine troubleshooting) No fuel. Low oil (if equipped with low oil shutdown). Pressure builds up after two pulls on the recoil starter or after initial use. Not primed or choked. Spark plug wire not attached. Engine ON/OFF switch in OFF position (If applicable.) Choke lever in the “Choke” position on a “hot” engine or an engine that has been exposed to thermal heat for a long perio

PRESSURE WASHER TERMINOLOGY PSI: Pounds per Square Inch. The unit of measure for water pressure. Also used for air pressure, hydraulic pressure, etc. GPM: Gallons Per Minute. The unit of measure for the flow rate of water through the pressure washer. CU: Cleaning Units. GPM multiplied by PSI. Bypass Mode: In Bypass Mode, the pump is recirculating water because the trigger of the spray gun is not pulled. Chemical Injection: Feeds cleaning agents into the pump to mix with the pressurized water and

Operating the pressure washer with water supply shutoff will void your warranty. You should never run this pressure washer for more than 2 minutes without pulling the trigger to allow cool water to enter the pump and the heated (recirculated) water to exit. ASSEMBLY 1. Connect handle (a) and tube bracket (b) to frame using the hardware (c) supplied. 2. Assemble hose reel (d) as described in the hose reel instruction manual. d a b c 3. Connect wand to gun. Tighten securely. 4. Attach high pressur

GFCI has tripped 1. Push reset button on plug start up 2. Plug is not well connected or electric 2. Check plug, socket and fuses socket is faulty 3. Extension cord too long or wire size 3. Remove extension cord too small 4. Main voltage supply too low 4. Check that main supply voltage is adequate 5. Thermal safety switch has tripped 5. Switch off unit and allow motor to cool down Motor stops suddenly 1. Extension cord too long or wire size 1. Remove extension cord too small 2. Thermal safety swi

0. nozzle - Red. This nozzle delivers a pinpoint stream and is extremely powerful. It covers a very small area of cleaning. This nozzle should only be used on surfaces that can withstand this high pressure such as metal or concrete. Do not use on wood. 15. nozzle - Yellow. This nozzle delivers a powerful 15 degree spray pattern for intense cleaning of small areas. This nozzle should only be used on areas that can withstand the high pressure from this nozzle. 25. nozzle - Green. This nozzle deliv

Reset Figure 3 - Grounded plug/reset button Assembly Instructions and Parts List PW132000AV 2 ! IMPORTANT ! This pressure washer is equipped with a microswitch sensitive to water flow. This Instant Start/Stop switch (ISS) senses water flow in the pump. When the trigger is released, water stops flowing through the pump. The ISS then automatically turns the motor off to protect pump from overheating. OPERATION 1. Pull trigger on gun and hold. 2. Turn the “ON/OFF” switch to “ON”. 3. Release trigger

2. Reduce the speed of the gasoline engine (RPM). Slow the engine down and the water pressure will go down with it. Step 3 is for models PCH2627, PCH3030 and PCH3540HR. 3. Adjust the pressure regulator on the pump. Turn the pressure regulator knob counterclockwise to lower pressure. Refer to the illustrations to identify your pressure regulator. Once you have finished using your pressure washer, return the pressure regulator to its original position by turning it clockwise. DO NOT attempt to inc

Double Insulated symbol Do not use pressure that exceeds the operating pressure of any of the parts (hoses, fittings, etc.) in the pressurized system. Ensure all equipment and accessories are rated to withstand the maximum working pressure of the unit. Explosion hazard. • NEVER spray flammable liquids or use pressure washer in areas containing combustible dust, liquids or vapors. • Never operate this machine in a closed building or in or near an explosive environment 4 Do not spray electrical ap

• Never leave the wand unattended while the machine is running • Never tamper with the engine governor or attempt to alter factory settings Altering factory settings could damage the unit and will void the warranty • Always hold gun and wand firmly when starting and operating the machine • NEVER allow the unit to run with the trigger released (off) for more than one minute Resulting heat buildup will damage the pump • NEVER store the pressure washer outdoors or where it could freeze Freezing tem