Push up the projection and slide the cover in the “OPEN” direction. When closing the cover, slide the cover in the “CLOSE” direction till the click under the plug cover projection rides over the engine cover. Finally, push in the projection. (2) Removing the spark plug Use an attached box wrench to remove or install the spark plug. (3) Checking the spark plug The clearance between two electrodes of spark plug (see the figure left) is 0.7 to 0.8 mm. Adjust to the correct clearance when it is too

Keep handles free of oil and fuel. (1) (2) (3) (4) (5) 15meters 3 Start the Blower only in accordance with the instructions. Do not use any other methods for starting the engine (6) ! • Use the blower and the tools supplied only for applications specified. • Start the blower engine only after the entire tool has been assembled. Operation of the tool is permitted only after all the appropriate accessories are attached. • The engine is to be switched off immediately if there are any engine problem

Always wear protective gloves! CAUTION : Start the blower only after having assembled itcompletely. 1. ASSEMBLY OF BLOWER PIPES 1) Align grooves in the blower pipe with pegs on the blower housing and slide the pipe onto housing. 2) Turn the blower pipe clockwise to lock it into place. 2. ASSEMBLY OF VACUUM ATTACHMENT 1) Installing Vacuum pipe (nozzle) (1) Loosen the screw . and open the protector . . WARNING! When using this machine as a blower, be sure to confirm that the screw . is not loosene

THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY. MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF “MERCHANTABILITY” AND “FITNESS FOR A SPECIFIC PURPOSE,” AFTER THE ONE YEAR TERM OF THIS WARRANTY. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusio

• Never use the blower while under the influence of alcohol or drugs (2). • Do not use the unit when you are tired. • Save these instructions for future referral. Personal Protective Equipment • The clothing worn should be functional and appropriate, I. e. It should be tight-fitting but not cause a hinderance. Do not wear jewelry, clothing or long hair which could be drawn into the air intake. • In order to avoid head-, eye-, hand- or foot injuries as well as to protect your hearing the followin

Inspection and Refill of Engine Oil (1) Perform the following procedure, with the engine cooled down. • Inspection: Please inspect whether it makes the machine horizontal, removes the oil cap, there is a oil to inside the range of the upper limit lower limit mark of gauge. When it is insufficient, (especially, when it has not reached to the lower limit level), please refill new oil. • Refill: Verticality (under the suction port cover) please do the machine, remove the oil cap. When oil is suppli

(9) Rotation of the engine speed stabilizes and when from low speed making at high speed rotation, if reaches the point where it accelerates smoothly, it is completion of warming-up. (2) Stop Switch (6) Primer pump Close(3) (4) (7) Open 11 NOTE • The engine may be damaged if the choke lever is moved further beyond the “CLOSE” position. • If the engine stops with an explosion sound or if the engine started, but stopped before operation of the choke lever, return this lever to the “OPEN” position

Conservez soigneusement ce manuel. Importante: Las bien este manual antes de poner el soplador en funcionamiento, y observe estrictamente las medidas de seguridad. Conserve este manual de instrucciones. INSTRUCTION MANUAL INSTRUCTIONS D’EMPLOI INSTRUCCIONES DE MANEJO English English Thank you very much for selecting the DOLMAR blower. We are pleased to be able to offer you the DOLMAR blower which is the result of a longdevelopment programme and many years of knowledge andexperience. The blower m

Clean the blower immediately after fuel has been spilt. Allow wet cloths to dry before disposing in properly, covered container to prevent spontaneous combustion. • Avoid any fuel contact with your clothing. Change your clothing immediately if fuel has been spilled on it (fire hazard). • Inspect the fuel cap at regular intervals making sure that it stays securely fastened. • Carefully tighten the locking screw of the fuel tank. Change locations to start the engine (at least 3 meters away from th

• Never service or store the blower in the vicinity of open flames, sparks, etc. (11). • Always store the blower in a well-ventilated locked room and with an emptied fuel tank. Observe and follow all relevant accident prevention instructions issued by the trade associations and by insurance companies. Do not perform any modifications to the blower as this will risk your safety. The performance of maintenance or repair work by the user is limited to those activities as described in this instructi