|
Фрагмент инструкции
2) Remove the base cover assembly. Remove the empty spool from the housing and discard any remaining line. REWINDING NEW LINE 3) Prepare 2 lengths (8ft each) of 2.4 mm nylon line. Thread 1 end of each line into the two holes on opposite sides of the spool. Pinch the exposed ends flat with a pair of pliers to prevent them slipping through the hole. 4) Wind the two lines in the same direction around the spool. REASSEMBLY 5) Slide the end of the two lines into the grooves to hold the line temporarily. 6) Position the spool back into the housing and pull the line through the eyelets. 7) Pull about 12cm (5ins) of line out on either side. 8) Reassemble the nylon string head as illustrated; mower gauge,spring and locking nut (tighten in an anti-clockwise direction). 9) N.B: In order to extend the nylon line as it wears down, pull the mower gauge downwards and turn it in a clockwise direction to feed out the desired length of line. O. Ecology This chapter is about how to maintain the ” eco features” of the machine as originally developed by our engineers, the correct use of this machine and handling of waste oil and fuel. 1. Research on the 4 stroke engine has been developed in order to produce lower fuel consumption and low emission of polluting exhaust gases 2. Use of the machinery: During the fuel filling operation particular care should be taken to avoid waste fuel polluting the enviroment. 3. When storing for a long period, empty fuel tank and run engine until dry, observing the same precautions as when filling. 4. Disposal of machines: Old machines can be very dangerous for the environment - do not throw them awway!! Please apply to the compotent body authorised to collect industrial waste. As prescribed by National laws on enviroment Technical data DISPLACEMENT (cm3) 34 38 42 46 BORE AND STROKE (mm) 38x30 40x30 41x32 43x32 ENGINE OUTPUT (Kw) 1,2 1,3 1,6 1,8 ENGINE SPEED AT MAX POWER (min-1) 8.000 8.000 8.000 8.200 MAXIMUM SPEED, NO LOAD (min-1) 10.000 10.000 10.000 11.000 MINIMUM SPEED (min-1) 2.800 2.800 2.800 2.800 BLADE SHAFT SPEED (min-1) 7.700 7.700 7.700 8.500 BLADE LOCKING NUT TIGHTENING TORQUE (Nm) 17 17 17 17 DRY WEIGHT (kg) 7,1 7,3-8,3 PRO 7,4-8,4 PRO-8,8 BP 7,7-8,7 PRO-10,8 BP FUEL TANK CAPACITY (cm3) 900 900 900 900 SOUND PRESSURE LEVEL (AT THE OPERATOR’S EAR) LpAav (dBA) (ISO7917) 97 97 97 106 GUARANTEED NOISE LEVEL LwAav (dBA) (ISO 10884) 114 114 114 114 MEASURED SOUND POWER LEVEL LwAav (dBA) (ISO 10884) 113 113 113 113 VIBRATIONS LEVEL STRING HEAD (ISO 7916) (m/s2) MAX-MIN 8,2-1,6 8,2-1,7 10,55-1,8 12,5-1,06 VIBRATIONS LEVEL BLADE (ISO 7916) (m/s2) MAX-MIN 8,2-1,6 8,2-1,7 16,38-1,8 17,79-1,06 ENGLISH - 7 Fault finding table Engine will not start Engine runs badlyor looses powerwhen cutting The machine runs but does not cut well Check STOP switch is in the position I. • Control fuel level min. 25%tank capacity. • • Check air filter is clean. • • Remove spark plug, dry it, clean it and adjust it, and replace it, if necessary. • • Chan...
Эта инструкция также подходит к моделям:Машинки для стрижки - Elite 3325/34 cc (729.38 kb)
Машинки для стрижки - 95390038700 (729.38 kb)
Машинки для стрижки - Elite 4230X/42 cc (729.38 kb)
Машинки для стрижки - Elite 4330X (729.38 kb)