Оценок - 4, средний балл: 4.3 ( )

Производитель: Electrolux Размер: 729.38 kb Название файла: Язык инструкции:

1. Research on the 4 stroke engine has been developed in order to produce lower fuel consumption and low emission of polluting exhaust gases 2. Use of the machinery: During the fuel filling operation particular care should be taken to avoid waste fuel polluting the enviroment. 3. When storing for a long period, empty fuel tank and run engine until dry, observing the same precautions as when filling. 4. Disposal of machines: Old machines can be very dangerous for the environment - do not throw them awway!! Please apply to the compotent body authorised to collect industrial waste. As prescribed by National laws on enviroment Technical data DISPLACEMENT (cm3) 34 38 42 46 BORE AND STROKE (mm) 38x30 40x30 41x32 43x32 ENGINE OUTPUT (Kw) 1,2 1,3 1,6 1,8 ENGINE SPEED AT MAX POWER (min-1) 8.000 8.000 8.000 8.200 MAXIMUM SPEED, NO LOAD (min-1) 10.000 10.000 10.000 11.000 MINIMUM SPEED (min-1) 2.800 2.800 2.800 2.800 BLADE SHAFT SPEED (min-1) 7.700 7.700 7.700 8.500 BLADE LOCKING NUT TIGHTENING TORQUE (Nm) 17 17 17 17 DRY WEIGHT (kg) 7,1 7,3-8,3 PRO 7,4-8,4 PRO-8,8 BP 7,7-8,7 PRO-10,8 BP FUEL TANK CAPACITY (cm3) 900 900 900 900 SOUND PRESSURE LEVEL (AT THE OPERATOR’S EAR) LpAav (dBA) (ISO7917) 97 97 97 106 GUARANTEED NOISE LEVEL LwAav (dBA) (ISO 10884) 114 114 114 114 MEASURED SOUND POWER LEVEL LwAav (dBA) (ISO 10884) 113 113 113 113 VIBRATIONS LEVEL STRING HEAD (ISO 7916) (m/s2) MAX-MIN 8,2-1,6 8,2-1,7 10,55-1,8 12,5-1,06 VIBRATIONS LEVEL BLADE (ISO 7916) (m/s2) MAX-MIN 8,2-1,6 8,2-1,7 16,38-1,8 17,79-1,06 ENGLISH - 7 Fault finding table Engine will not start Engine runs badlyor looses powerwhen cutting The machine runs but does not cut well Check STOP switch is in the position I. • Control fuel level min. 25%tank capacity. • • Check air filter is clean. • • Remove spark plug, dry it, clean it and adjust it, and replace it, if necessary. • • Change fuel filter. Contact your dealer. • Carefully follow the cutting accessory assembly instructions. • Check metal cutting accessory is sharp. Otherwise, contact your dealer. • Engine still gives trouble: contact your dealer. ENGLISH - 8 A BACK-PACK BRUSHCUTTER 1 Insert the flexible drive shaft onto the engine connector (G). Ensure the male square end of the shaft engaged firmly into the female square end of the connector. Insert throttle cable and electrical wires (A) into the retaining guide (B) far enough to allow the necessary connections to be made (see Fig. 1A). Tighten screw (V) ensuring it locates correctly into its opening (S). Now the shaft is firmly fixed in the connector. 2 Pull the plastic ring nut (C) away from the end of the rigid tube turning it counterclockwise if necessary. Insert the rigid tube into the handle section until the label (F) is aligned with the edge of the plastic threaded rim (P). These procedures will ensure a correct fit between both male and female connectors. 3 Tighten the ring nut (C) hand tight. Follow the standard instructions mentioned earlier in this manual to connect the t...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: