Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Underwriters Laboratories. This symbol This symbol designates that designatesThis symbol designates this tool is listed by that that this tool is listed by Underwriters Laboratories, this tool the Canadian Standards and listed to Canadian compliesAssociation. Standards by Underwriters to NOM Laboratories. Mexican Standards. This symbol designates that this tool is listed by Intertek Testing Services. -5 BM 2610956795 12-07 12/12/07 1:27 PM Page 6 Functional Description and Specifications !WARNING Disconnect the plug from the power source before making any assembly, adjustments or changing accessories. Such preventive safety measures reduce the risk of starting the tool accidentally. Reciprocating Saw FIG. 1 VIBRATION DAMPER RUBBERIZED SOFT GRIP SWIVEL CORD VENTILATIONFOOTPLATE OPENINGS PIVOTING FOOTPLATE LockJaw™ BLADE HOLDER VARIABLE SPEED CONTROLLED TRIGGER SAW BLADE RELEASE LEVER RUBBER BOOT HANDLE / SAW MECHANISM VARIABLE SPEED DIAL “LOCK-ON” BUTTON BLADE ORBIT SELECTOR NOTE: For tool specifications refer to the nameplate on your tool. -6 BM 2610956795 12-07 12/12/07 1:27 PM Page 7 Assembly Preparing the Saw BLADE SELECTION No one blade can be efficient on all cutting jobs. Different materials require specially designed blades. Since your reciprocating saw can cut so many materials, many types of BOSCH blades are available. Be sure to use the proper blade to ensure proper cutting performance. INSTALLING A BLADE !WARNING Unplug tool from power source before changing blade or making any adjustments. 1. Insert the blade into the LockJaw™ blade holder until the locking collar automatically rotates clockwise and locks the blade in place (Fig. 2). Note: if the blade will not lock automatically, rotate the locking collar counterclockwise until it clicks and locks in the open position (Fig. 3). 2 Push in and pull out on the blade to be sure the pin in the clamp housing goes through the hole in the blade to hold the blade securely. The blade may be inserted with the teeth facing down or up. 3. To remove the blade, rotate the locking collar counter-clockwise and the blade will automatically eject from the LockJaw™ blade holder and lock the collar in the open position. !WARNING Make sure that the front end of the blade extends through the footplate for the entire stroke length. Do not use specialty blades that are very short or those with a significant cant. Blade must not contact footplate. A blade which is too short or tilted could jam inside the foot and snap. FIG. 3FIG. 2 Open Position LockJaw™ BLADE HOLDER LOCKING COLLAR BLADE LOCKING COLLAR Operating Instructions VARIABLE SPEED CONTROLLED TRIGGER SWITCH Your tool is equipped with a variable speed controlled trigger switch. The tool can be turned "ON" or "OFF" by squeezing or releasing the trigger. The blade plunger stroke rate can be adjusted from the minimum to maximum nameplate stroke rate by the pressure you apply to the trigger. Apply more pressure to increase the speed and release pressure to decrease speed (Fig. 1). "LOCK-ON" BUTTON The "Lock-ON" button, located in the handle of your tool allows for continuous operation at maximum SPM without holding the trigger (Fig. 1). -7 TO LOCK TRIGGER "ON": squeeze trigger, depress button and release trigger. TO UNLOCK THE TRIGGER: squeeze trigger and release it without depressing the "Lock- ON" button. !WARNING If the “Lock-ON” button is continuously being depressed, the trigger can not be released. VIBRATION DAMPER HANDLE / SAW MECHANISM The integrated vibration damper in the main handle and saw mechanism reduces vibrations to the main handle (Fig. 1). BM 2610956795 12-07 12/12/07 1:27 PM Page 8 VARIABLE SPEED DIAL Your tool is equipped with a variable speed dial. The blade stroke rate may be adjusted during cutting operation by presetting the dial on or between any one of the six numbers (Fig. 1). Setting SPM rating (strokes per minute) 1Low stroke speed 2-3 Medium stroke speed 4 High stroke speed ORBIT SELECTOR To obtain the best cutting advance in various types of materials, your saw has a blade orbit selector to adjust the swing of the saw blade. When cutting into wood and plastic, as well as other soft materials, a larger swing of the blade is desired. There are two orbit selector positions. The non-orbit position (metal), move the orbit selector lever toward the and for a full orbit (wood), move the selector lever toward the (Fig. 4). The non-orbit gives the best cutting advance and extends blade life when cutting steel and similar hard materials which have more Higher speed settings are generally used for fast cutting or when softer cutting materials such as wood, composite materials, and plastics. Slower speed settings are generally used when precision is required or when cutting harder materials. Materials typically cut using slower speeds include sheet metal, conduit, and pipe. resistance to cut. For materials that have less resistance to cut, the orbit position can be selected for the best cutting ad...