Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
Their thin kerf and tooth design deliver the best speed, quality of cut, and reduce battery drain. Use of standard blades will substantially affect the performance and reduce run-time. -8 BM 2610914527 3/03 3/18/03 10:47 AM Page 9 Assembly ATTACHING THE BLADE Do not use wrenches with longer handles, Disconnect battery pack since it may lead to over tightening of the from tool or place the blade stud. ! WARNING -9- FIG. 2 TIGHTEN LOOSEN BLADE STUD LOWER GUARD SPRING OUTER WASHER Large Diameter Faces Blade INNER WASHER Large Diameter Faces Blade BLADE LOWER GUARD BLADE SHAFT UPPER GUARD WRENCH OUTER WASHER MARK switch in the locked or off position before making any assembly, adjustments or changing accessories. Such preventive safety measures reduce the risk of starting the tool accidentally. 1. Turn BLADE STUD with wrench provided clockwise and remove BLADE STUD and OUTER WASHER (Fig. 2). If the shaft moves while attempting to loosen the blade stud press the lock button (Fig. 1). 2. Retract the lower guard all the way up into the upper guard. While retracting the lower guard, check operation and condition of the LOWER GUARD SPRING. 3. Make sure the saw teeth and arrow on the blade point in the same direction as the arrow on the lower guard. 4. Slide blade through slot in the foot and mount it against the INNER WASHER on the shaft. Be sure the large diameter of the OUTER washer lays flush against the blade. 5. Reinstall OUTER WASHER and tighten BLADE STUD finger tight. The face of outer washer has marks around it that will help you properly adjust the blade stud. Press lock button to lock shaft and TIGHTEN BLADE STUD COUNTER-CLOCKWISE ONE MARK ON BLADE WASHER WITH THE WRENCH PROVIDED. VARI-TORQUE CLUTCH This clutching action is provided by the friction of the OUTER WASHER against the BLADE and permits the blade shaft to turn when the blade encounters excessive resistance. When the BLADE STUD is properly tightened (as described in No. 5 of Attaching The Blade), the blade will slip when it encounters excessive resistance, thus reducing saw’s tendency to KICKBACK. One setting may not be sufficient for cutting all materials. If excessive blade slippage occurs, tighten the blade stud 1/2 mark more. OVERTIGHTENING THE BLADE STUD NULLIFIES THE EFFECTIVE-NESS OF THE CLUTCH. DUST EXTRACTION Your tool is equipped is with a dust port for dust and chip extraction. To use this feature, open dust port cover and attach vacuum hose (optional accessory) to the dust port, and connect opposite end the hose to a shop vacuum cleaner. ! WARNING To prevent personal injury, always position vacuum hose so that it does not interfere with the lower guard, or the cutting operation at all settings. BM 2610914527 3/03 3/18/03 10:47 AM Page 10 Operating Instructions DEPTH ADJUSTMENT Disconnect battery pack from tool. Loosen setting desired. Check desired depth (Fig. 3). the depth adjustment knob located on the Not more than one tooth length of the bladeback side of the upper guard. Hold the foot should extend below the material to be cut, down with one hand and raise or lower saw for minimum splintering (Fig. 4). by the handle. Tighten knob at the depth 0 2 1 FIG. 3 CALIBRATED DEPTH BRACKET DEPTH ADJUSTMENT KNOB BLADE WRENCH & STORAGE AREA FIG. 4 ONE TOOTH LENGTH SHOULD PENETRATE WOOD FOR MINIMUM SPLINTERING SAFETY SWITCH 90° CUTTING ANGLE CHECK The safety switch is designed to prevent accidental starts. To operate safety switch, press the release button with your thumb on either side of handle to disengage the lock, then pull the trigger (Fig. 5). When the trigger is released the button will engage the safety switch automatically, and the trigger will no longer operate. (See Switch & General Cuts on page 11.) FIG. 5 SAFETY SWITCH RELEASE BUTTON TRIGGER Disconnect battery pack from tool. Set foot to maximum depth of cut setting. Loosen bevel adjustment knob, set to 0° on quadrant, retighten knob and check for 90° angle between the blade and bottom plane of foot with a square (Fig. 6). Make adjustments by turning the small alignment screw, if necessary (Fig. 7). FIG. 7FIG. 6 BEVEL ADJUSTMENT KNOB 90°FOOT ALIGNMENTSCREW BLADE -10 BM 2610914527 3/03 3/18/03 10:47 AM Page 11 BEVEL ADJUSTMENT Disconnect battery pack from tool. The foot can be adjusted up to 45° by loosening the bevel adjustment knob at the front of the saw. Align to desired angle on calibrated quadrant. Then tighten bevel adjustment knob (Fig. 8). For 50° loosen bevel adjustment knob, depress 45° stop spring (Fig. 9), align foot to 50 mark on quadrant and tighten knob. Because of the increased amount of blade engagement in the work and decreased stability of the foot, blade binding may occur. Keep the saw steady and the foot firmly on the workpiece. ADJUSTABLE LINE GUIDE For a straight 90° cut you can use the left or right side of notch in the foot. For 45° bevel cuts, use the right side (Fig 9). The guide can be adjusted to allow for variation in blade thicknesses for whicheve...
Эта инструкция также подходит к моделям:Лобзики и пилы - 1662 (665.17 kb)