Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
Max. saw blade O 250 mm Saw blade arbor bore O 30 mm Max. blade speed 4000 min-1 Max. depth of cut 80 mm Safety devices Riving knife The riving knife prevents the workpiece from being caught by the rising teeth of the saw blade and being thrown against the operator. Always have riving knife installed during operation. Blade guard The blade guard protects against accidental contact with the blade and keeps chips from flying about. Always have blade guard installed during operation. Push stick The push stick serves as an extension of the right hand and protects against accidental contact with the saw blade. Always use push stick if distance between rip fence and saw blade is . 120 mm. In order for the push stick to be always at hand, it can be stored in a sheath in the machine's housing. PK 255 2.5 Operating controls On/off switch with emergency stop · To switch ON = press green button. · To switch OFF = press red button or cover of on/ off switch. 3 An undervoltage relay trips in the event of a voltage failure, to prevent a restarting of the saw when the power is restored. To start the saw again after a power failure press the green button. To prevent unauthorized use the switch can be blocked with a padlock. Handwheel for blade tilt setting The saw blade can be tilted steplessly between 0° and 45°. The centre of motion is at saw table level, so the depth of cut remains the same, regardless of the bevel angle. Ratchet lock lever The set bevel angle can be locked with a ratchet lock lever, so it does not change during sawing. 3 There are several ratchet lock levers on the saw. If the swivelling range is not sufficient, the lever position can be shifted: pull lever up, turn and let engage again. Handwheel for setting the depth of cut The depth of cut can be adjusted by turning the handwheel. 3 To compensate for possible play in the blade height setting mechanism, always raise the blade to the desired position. 25 20 30 35 25 20 30 35 25 20 15 10 5 0 30 35 25 20 15 10 5 0 30 35 2.6 PK 255 Rip fence The rip fence slides onto the saw from the righthand side and locks on the saw’s front. The auxiliary fence extrusion can be repositioned after loosening the two wing nuts: · small edge (as shown): - for cutting thin stock; - when the saw blade is tilted. · wide edge: - for cutting thick stock (max. 65 mm). Mitre fence The mitre fence can be fitted into groove of either the sliding carriage or the saw table. It is locked in the groove with the ratchet lock lever (black arrow). For mitre cuts the fence extrusion turns through 45° in both directions. To set a mitre angle loosen lock lever (grey arrow). Assembly and connection Installation of legs 1. Put a rubber foot on each of the four legs (on the side with the skewed corner). 2. Turn saw over and place on the saw table. 3. Insert legs into recesses at the corners of the machine housing. 4. Fasten legs with 4 each - hexagon head screw M 8x16; - serrated lock washer; - washer; - hexagon nut M 8. 5. Stand saw on its feet 6. Retighten fastening screws on all four legs. Connect to dust collector ADanger! Some kinds of wooden dust (e.g. from oak and ash) can be carcinogenic when inhaled. When working indoors always connect to a suitable dust collector (air speed at suction port of saw . 20 m/s). A Caution! Operation without a dust collector is only possible - outdoors; - for a short duration (up to max. 30 minutes); - with a dust mask. If no dust collector is connected saw dust and chips build up inside the chip case. These need to be removed after latest 30 minutes of operation. Dust collection ports are provided on the saw blade guard and the chip case. 25 20 15 10 5 0 30 35 30 45 15 0 15 30 45 PK 255 2.7 Dust collection from chip casing 1. Turn saw upside down. 2. Remove transport support inside the saw housing. 3. Attach suction port to chipcase with - 3 ea. hex. head screw M 6x13 - 3 ea. washer - 3 ea. serrated lock washer - 3 ea. hexagon nut M 6 3 If you are using a dust collector, connect to the chip case's suction port. Dust collection from blade guard 1. Fit blade guard to riving knife. The lower edge of the blade guard should be in a horizontal position. 3 If you are using a dust collector, connect the blade guard's dust spout with the dust collector as well. Mitre fence 1. Screw long stud screw into centre tapped hole of the guide bar and tighten. 2. Screw short stud screw into tapped hole of the guide bar. 3. Place angle plate on stud screws (short stud screw into oblong hole). 4. Fit spacer bushing and washer to long stud screw and screw on the ratchet lock lever. 5. Put large washer on short stud screw and screw on ratchet lock lever. 6. Fit two cup square neck screws into the fence extrusion’s groove and put the screw’s threaded ends though the oblong holes. 7. Fit a washer to each of the screws and screw on a knurled nut 8. Fit a cup square neck screw into the upper groove of the fence extrusion and attach the flip stop as illustrated. 9. Screw extrusion e...
Эта инструкция также подходит к моделям:Лобзики и пилы - PK 255 3 (607.95 kb)
Лобзики и пилы - PK 255 2 (607.95 kb)
Лобзики и пилы - 5 WN (607.95 kb)