Войти:
Оценок - 2, средний балл: 5 ( )

Инструкция по эксплуатации Elektra Beckum, модель 5 WN

Производитель: Elektra Beckum
Размер: 607.95 kb
Название файла:
Язык инструкции:
Перейти к скачиванию



Фрагмент инструкции


Saw blade change ADanger! Risk of injury by the saw blade’s teeth. Wear gloves when changing blades. 1. Remove the two fastening screws of the removable table section. 2. Lift removable table section up and remove. 3. Raise blade fully. 4. Take blade guard off. 5. Lift chip case cover slightly and swing to the side. The cover is hooked into the bottom of the chip case and can not fall down. 25 20 15 10 5 0 30 35 2.10 PK 255 6. To block the saw blade insert lock bar into hole in the saw table and turn saw blade by hand until lock bar engages in saw spindle hole. 7. Loosen saw blade spindle arbor nut with spanner (L.H. thread!). 8. Take outer blade collar and saw blade off the saw spindle. 9. Clean clamping surfaces of saw spindle and saw blade. ADanger! Do not use cleaning agents (e.g. for removing resin residue) that could corrode the light metal components of the saw; the stability of the saw would be adversely affected. 10. Put on a fresh saw blade (observe direction of rotation). The saw spindle’s driving pin must fit into one of the saw blade’s two pin holes. ADanger! Use only suitable saw blades (see „Technical specifications“) – when using unsuitable or damaged blades parts could be explosivelike hurled from it by the centrifugal force. Do not use: - saw blades made of high speed steel (HSS); - saw blades with visible damage; - cut-off wheel blades. ADanger! - Mount saw blade only using genuine parts. - Do not use loose-fitting reducing rings; the saw blade could work loose. - Saw blades have to be mounted in such way that they do not wobble or run out of balance, and can not work loose during operation. 11. Slide outer blade collar onto saw spindle. The saw spindle’s driving pin must fit into the pin hole of the outer blade collar. 12. Screw arbor nut, with the low side facing the blade, onto the saw spindle (L.H. thread!). Tighten fingertight only with the tool supplied. ADanger! - Do not extent the arbor nut wrench. - Do not tighten arbor nut by tapping on the wrench. - After tightening the arbor nut do not forget to remove the saw spindle lock bar! 13. Slide chip case cover back into the closed position and tighten screws. 14. Fasten removable table section. Saw blade adjustment The saw blade must run exactly parallel with the saw table’s edge. The distance between the table’s edge and the blade shall be not more than 3 mm. Adjustment is done from the top with setting nuts. This setting is then fixed by two counter nuts on the underside of the saw: 1. Remove the two fastening screws of the removable table section. 2. Lift removable table section up and remove. 3. Lift chip case cover slightly and swing to the side. The cover is hooked into the bottom of the chip case and can not fall down. 4. Tighten two each setting nuts on the swivel segments against each other. 3 The swivel segments’ setting nuts must not be tightened during operation of the saw, as this would create mechanical twisting...

Эта инструкция также подходит к моделям:
Лобзики и пилы - PK 255 3 (607.95 kb)
Лобзики и пилы - 4 DN (607.95 kb)
Лобзики и пилы - PK 255 2 (607.95 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории