Войти:
Оценок - 2, средний балл: 3.5 ( )

Инструкция по эксплуатации Elektra Beckum, модель PK 255 2

Производитель: Elektra Beckum
Размер: 607.95 kb
Название файла:
Язык инструкции:
Перейти к скачиванию



Фрагмент инструкции


4. To check the setting of the 45° backstop, repeat steps 1 to 3 accordingly. 5. After resetting any of the backstops, check bevel tilt scale on the machine’s front, adjust if necessary. Scale setting The rip fence scale needs to be set according to the position and thickness of the saw blade. 1. Place rip fence against the right-hand edge of the saw blade and lock in position. The "0"-mark of the scale should now be directly underneath the left-hand edge of the rip fence extrusion (arrow). If not: - loosen fixing screw and reposition scale. - tighten fixing screw and remove rip fence. 0 Universal fence adjustments 1. Check if fence is square against saw blade with a try square. 2. If necessary, loosen fixing screws and adjust mitre scale. 3. Retighten fixing screws. Cleaning the saw 1. Lay machine on its side. 2. Remove chips and saw dust with vacuum cleaner or brush: - from saw blade setting guide elements - from motor vent slots Machine transportation · Lower saw blade completely before transportation. · Use original packing, if possible. Machine storage ADanger! Store machine so that - it can not be started by unauthorized persons, and - nobody can get injured. 3 The on/off buttons can be blocked with a padlock. A Caution! Do not store machine outdoors or in damp environment without protection. Service plan 3045 15 0 15 30 45 Before switching ON - Chip ejection (when operated without dust collec- tion) and - table slot Visual check if unob- structed by chips. Riving knife Visual check if dis- tance saw blade – riv- ing knife is 3...8 mm. Monthly (if used daily) Clean guide elements for saw blade setting - threaded rods for blade rise and fall; - swivel segments. - Remove chips with vacuum cleaner or brush; - apply light coat of oil to guide ele- ments. Power cable Check for damage, if necessary have replaced by a qualified electrician. Every 300 hours of operation Saw blade drive belt Check tension (R 5 mm) All screwed connec- tions Check, retighten if nec- essary (except saw blade longitudinal shift setting screws). Universal fence adjustments 1. Check if fence is square against saw blade with a try square. 2. If necessary, loosen fixing screws and adjust mitre scale. 3. Retighten fixing screws. Cleaning the saw 1. Lay machine on its side. 2. Remove chips and saw dust with vacuum cleaner or brush: - from saw blade setting guide elements - from motor vent slots Machine transportation · Lower saw blade completely before transporta- tion. · Use original packing, if possible. Machine storage ADanger! Store machine so that - it can not be started by unauthorized per- sons, and - nobody can get injured. 3 The on/off buttons can be blocked with a pad- lock. A Caution! Do not store machine outdoors or in damp environment without protection. Service plan 3045 15 0 15 30 45 Before switching ON - Chip ejection (when operated without dust collec- tion) and - table slot Visual check if unob- structed by chips. R...

Эта инструкция также подходит к моделям:
Лобзики и пилы - PK 255 3 (607.95 kb)
Лобзики и пилы - 4 DN (607.95 kb)
Лобзики и пилы - 5 WN (607.95 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории