Войти:
Сортировка : Названию ↑   Загрузкам   Оценке   Размеру ↑  
Скачали: 8   Размер: 149 kb   Производитель: Makita  
Категория: Кромочные фрезеры
@name

The stopper block is also convenient for making three passes with progressively deeper bit settings when cutting deep grooves. CAUTION: • When using a bit having total length of 60 mm (2 - 3/8”) or more, or edge length of 35 mm (1 - 3/8”) or more, the depth of cut cannot be adjusted as previously mentioned. To adjust, proceed as follows: Loosen the lock lever and carefully adjust bit protrusion below the tool base to the desired depth of cut by moving the tool body up or down. Then re-tighten th

Скачали: 24   Размер: 205 kb   Производитель: Makita  
Категория: Кромочные фрезеры
@name

SYMBOLS USD101-2 The followings show the symbols used for tool. V ....................... volts ................alternating current A .......................amperes n....................no load speed ° Hz ..................... hertz .../min................revolutions or reciprocation per minute FUNCTIONAL DESCRIPTION 003654 12 3 4 7 6 5 1. Lock lever 2. Adjusting knob 3. Depth pointer 4. Fast-feed button 5. Stopper pole 6. Fast-feed button 7. Stopper pole setting nut 003656 1 1. Nylon nut CAUTIO

Скачали: 5   Размер: 170 kb   Производитель: Makita  
Категория: Кромочные фрезеры
@name

They may cause cracks in the tool base. 16. Draw attention to the need to use cutters of the correct shank diameter and suitable for the speed of the tool. 17. Some material contains chemicals which may be toxic. Take caution to prevent dust inhalation and skin contact. Follow material supplier safety data. SAVE THESE INSTRUCTIONS WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. SYMBOLS USD101-2 The followings show the sym

Скачали: 5   Размер: 156 kb   Производитель: Makita  
Категория: Кромочные фрезеры
@name

If you use this tool unsafely or incorrectly, you can suffer serious personal injury. 1. Hold tool by insulated gripping surfaces 4. Check the bit carefully for cracks or dam- when performing an operation where the age before operation. Replace cracked or cutting tool may contact hidden wiring or damaged bit immediately. its own cord. Contact with a “live” wire will 5. Avoid cutting nails. Inspect for and make exposed metal parts of the tool “live” remove all nails from the workpiece and shock t

Скачали: 2   Размер: 208 kb   Производитель: Makita  
Категория: Кромочные фрезеры
@name

Moving the tool forward too slowly may burn and mar the cut. The proper feed rate will depend on the bit size, the kind of workpiece and depth of cut. Before beginning the cut on the actual workpiece, it is advisable to make a sample cut on a piece of scrap lumber. This will show exactly how the cut will look as well as enable you to check dimensions. CAUTION: • Since excessive cutting may cause overload of the motor or difficulty in controlling the tool, the depth of cut should not be more than

Скачали: 13   Размер: 170 kb   Производитель: Makita  
Категория: Кромочные фрезеры
@name

Apply caution when locking tool in “ON” position and maintain firm grasp on tool. To start the tool, move the switch lever to the I (ON) position. To stop the tool, move the switch lever to the O (OFF) position. Motor unit cord 2. Outlet 3. Lock button 4. Switch trigger 003663 For RD1100 and RD1101 1 CAUTION: • Before plugging in the tool, always check to see that the 2 switch trigger actuates properly and returns to the “OFF” 3 position when released. 4 • Switch can be locked in “ON” position f

Скачали: 12   Размер: 107 kb   Производитель: Makita  
Категория: Кромочные фрезеры

Скачали: 25   Размер: 962 kb   Производитель: Makita  
Категория: Кромочные фрезеры
@name

Replace cracked or damaged bit immediately. 3.Avoid cutting nails. Inspect for and remove all nails from the workpiece be- fore operation. 4. Hold the tool firmly with both hands. 5. Keep hands away from rotating parts. 6. Make sure the bit is not contacting the workpiece before the switch is turned on. 7. Before using the tool on an actual workpiece, let it run for a while. Watch for vibration or wobbling that could indicate improperly installed bit. 8. Be careful of the bit rotating direction

Скачали: 4   Размер: 130 kb   Производитель: Makita  
Категория: Кромочные фрезеры

Скачали: 71   Размер: 179 kb   Производитель: Makita  
Категория: Кромочные фрезеры
@name

Do not force it past 5 or 1, or the speed adjusting function may no longer work. CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. 003670 Installing or removing the bit CAUTION: • Install the bit securely. Always use only the wrench provided with the tool. A loose or overtightened bit can be dangerous. • Do not tighten the collet nut without inserting a bit or install small shank bits without using a collet sleeve. Either can lead to





Категории