Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
Moving the tool forward too slowly may burn and mar the cut. The proper feed rate will depend on the bit size, the kind of workpiece and depth of cut. Before beginning the cut on the actual workpiece, it is advisable to make a sample cut on a piece of scrap lumber. This will show exactly how the cut will look as well as enable you to check dimensions. CAUTION: • Since excessive cutting may cause overload of the motor or difficulty in controlling the tool, the depth of cut should not be more than 3 mm (1/8”) at a pass when cutting grooves. When you wish to cut grooves more than 3 mm (1/8”) deep, make several passes with progressively deeper bit settings. 001986 Templet guide The templet guide provides a sleeve through which the bit passes, allowing use of the trimmer with templet patterns. 002006 Remove the tool base from the tool. Loosen the wing bolts and secure the tool base horizontally. Loosen the two screws on the tool base. 1. Base 2. Wing bolt 3. Screws 4. Screwdriver 1 2 1. Templet guide 2. Convex portions 002007 Place the templet guide on the tool base. There are four convex portions on the templet guide. Secure two of the four convex portions using the two screws. Install the tool base on the tool. 001988 Secure the templet to the workpiece. Place the tool on the templet and move the tool with the templet guide sliding along the side of the templet. NOTE: • The workpiece will be cut a slightly different size from the templet. Allow for the distance (X) between the router bit and the outside of the templet guide. The distance (X) can be calculated by using the following equation: Distance (X) = (outside diameter of the templet guide – router bit diameter) / 2 001989 Straight guide (optional accessory) The straight guide is effectively used for straight cuts when chamfering or grooving. 1 2 3 4 5 6 10mm(3/8") 1. Straight bit 2. Base 3. Templet 4. Distance (X) 5. Workpiece 6. Templet guide 10 001990 Attach the guide plate to the straight guide with the bolt, the wave washer, the flat washer and the wing nut. 1 2 3 4 5 6 001990 Attach the guide plate to the straight guide with the bolt, the wave washer, the flat washer and the wing nut. 1 2 3 4 5 6 1. Bolt 2. Guide plate 3. Straight guide 4. Flat washer 5. Wave washer 6. Wing nut 002008 Loosen the wing bolts and secure the tool base horizontally. Attach the straight guide with the clamp screw (A). Loosen the wing nut on the straight guide and adjust the distance between the bit and the straight guide. At the desired distance, tighten the wing nut securely. When cutting, move the tool with the straight guide flush with the side of the workpiece. 001985 NOTE: • When using the trimmer shoe, the straight guide or the trimmer guide, be sure to keep it on the right side in the feed direction. This will help to keep it flush with the side of the workpiece. 1. Clamp screw (A) 2. Straight guide 3. Wing bolt 4. Base 5. Wing nut 1 2 3 4 1. Feed direction 2. Bit revolving direction 3. Workpiece 4. Trimmer shoe, straight guide 002009 If the distance (A) between the side of the workpiece and the cutting position is too wide for the straight guide, or if the side of the workpiece is not straight, the straight guide cannot be used. In this case, firmly clamp a straight board to the work- piece and use it as a guide against the trimmer base. Feed the tool in the direction of the arrow. A 1 2 3 4 5 6 7 1 2 3 4 5 6 7 Wing nut 2. Wave washer 3. Flat washer 4. Guide plate 5. Straight guide 6. Centre hole 7. Bolt 1. Wing nut 2. Wave washer 3. Flat washer 4. Guide plate 5. Straight guide 6. Centre hole 7. Bolt Circular work Circular work may be accomplished if you assemble the straight guide and guide plate as shown in the figure. Min. and max. radius of circles to be cut (distance between the center of circle and the center of bit) are as follows: Min.: 70 mm (2-3/4”) Max.: 221 mm (8-11/16”) 001993 For cutting circles between 70 mm (2-3/4”) and 121 mm (4-3/4”) in radius. 001994 For cutting circles between 121 mm (4-3/4”) and 221 mm (8-11/16”) in radius. NOTE: • Circles between 172 mm (6-3/4”) and 186 mm (7-5/16”) in radius cannot be cut using this guide. 1 2 3 4 5 6 7 002010 Align the center hole in the straight guide with the center of the circle to be cut. Drive a nail less than 6 mm (1/4”) in diameter into the center hole to secure the straight guide. Pivot the tool around the nail in clockwise direction. 1. Nail 2. Centre hole 3. Straight guide 002011 Trimmer guide Trimming, curved cuts in veneers for furniture and the like can be done easily with the trimmer guide. The guide roller rides the curve and assures a fine cut. Loosen the wing bolts and secure the tool base horizontally. Install the trimmer guide on the tool base with the clamp screw (A). Loosen the clamp screw (B) and adjust the distance between the bit and the trimmer guide by turning the adjusting screw (1 mm (3/64”) per turn). At the desired distance, tighten the clamp screw (B) to secure the trimmer gui...