Besides the differences noted in this insert, all other content in the Model G0656 owner's manual applies to this machine. Before operating your new machine, you MUST read and understand this insert and the entire Model G0656 manual to reduce the risk of injury when using this machine. If you have any further questions about this manual insert or the differences between the Model G0656X and the Model G0656, contact our Technical Support at (570) 546-9663 or email techsupport@grizzlv. com. Mach

Consider existing and anticipated machine needs, size of material to be processed through each machine, and space for auxiliary stands or work tables. Also, consider the relative position of each machine to one another for efficient material handling. Lighting And Outlets Lighting should be bright enough to eliminate shadow and prevent eye strain. Electrical circuits should be dedicated or large enough to handle the amperage draw. Outlets should be located near each machine so power or extensi

CAUTION: The router will "kick" when started. If it comes into contact with the workpiece it could jump out of your hands and cause injury. 4. Smoothly move the router in the correct feed direction into the workpiece. CAUTION: DO NOT start routing at a corner. Starting at a corner may cause the router to grab, damaging the workpiece corner, and possibly causing personal injury. 5. Feed the router along the workpiece at a consistent rate of speed. Be aware of the sound of the router motor and the

........................................................................................................................................................................................................................................................................................................................................................... ... ......................................... ..........................................................................................................

These are mounted in the same manner as the standard rails. The long rail set also includes legs which provide added stability for the table saw/fence assembly when large or heavy work is positioned on the table. Mounting the extension legs 1. Attach rails according to the rail installation instructions on page 6 & 7. 2. Thread a 1.2" hex nut onto each foot and thread a foot into the bottom of each leg. 3. Loosely bolt a brace to each of the legs with a 3.8-16 x 3.4" hex bolt and three 3.8" wash

5. Thread the fence adjustment handle into the tapped hole on the top edge of the fence. 6. With the lock knob loose, the fence assembly should slide smoothly across the key way. Avoid letting the fence drag across the tables. Figure 5. Fence base lock knob attachment. Cutterhead Guard The cutterhead guard spring tension comes preset from the factory. To install the cutterhead guard: 1. Loosen the black plastic knob shown in Figure 6. 2. Slide the cutterhead assembly post into the slot shown in

Remove the RHN-18 overload relay and replace it with a RHN-10 (5.5-8.5A) type, with the dial set to 7A (Figure 4). Figure 4. Overload relays. 7 RHN-10 Overload Relay 4. Remove the CN-18 magnetic contact overload relay and replace it with a CN-11 type (Figure 5). Figure 5. Overload relays. 11 CN-11 Magnetic Contactor Overload Relay 5. Wire the motor as shown on the diagram on the inside of the motor wire cover. Note— The circled references on the diagrams represent labels on the wires. Also, Figu

702 P9859702 PULLEY 703 PK54M KEY 7 X 7 X 45 704 PSS08M SET SCREW 5.16"-18 X 1.2" 705 PN02M HEX NUT M10-1.5 706 PLW04 LOCK WASHER 3.8" 707 PB14M HEX BOLT M10-1.5 X 35 708 PW01 FLAT WASHER 1.2" 709 PB25M HEX BOLT M12-1.75 X 25 710 P9859710 MOTOR MOUNT PLATE 711 PVA47 V-BELT (A-47") 712 P9859712 Z SERIES LABEL 713 P9859713 SAFETY GLASSES WARNING 714 P9860714 MACHINE ID WARNING 715 P9859715 PUSH BLOCK WARNING 716 P9859716 CAST LOGO 801 P9860ZX801 COUNTERSUNK CAP SCREW 802 H2334 CARBIDE INDEXABLE CU

702 P9859702 PULLEY 703 PK54M KEY 7 X 7 X 45 704 PSS08M SET SCREW 5.16"-18 X 1.2" 705 PN02M HEX NUT M10-1.5 706 PLW04 LOCK WASHER 3.8" 707 PB14M HEX BOLT M10-1.5 X 35 708 PW01 FLAT WASHER 1.2" 709 PB25M HEX BOLT M12-1.75 X 25 710 P9859710 MOTOR MOUNT PLATE 711 PVA47 V-BELT (A-47") 712 P9859712 Z SERIES LABEL 713 P9859713 SAFETY GLASSES WARNING 714 P9860714 MACHINE ID WARNING 715 P9859715 PUSH BLOCK WARNING 716 P9859716 CAST LOGO 801 P9860ZX801 COUNTERSUNK CAP SCREW 802 H2334 CARBIDE INDEXABLE CU

#TR8349 PRINTED IN CHINA. ..........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................