Оценок - 2, средний балл: 4 ( )

Производитель: Vermont Casting Размер: 1.74 mb Название файла: Язык инструкции:

Apply the paint sparingly; two light coats of paint will give better results than a single heavy coat. Clean porcelain enamel surfaces with a soft, damp cloth. Do not use abrasive cleaning agents. If necessary, use only a cleaning agent formulated especially for use on porcelain enamel surfaces. CAUTION TURN THE PILOT OFF BEFORE PAINTING. ALLOW THE HEATER TO COOL COMPLETELY BEFORE PAINTING. Cleaning the Glass WARNING: Allow the glass cool completely before attempting to clean. It will be necessary to clean the glass periodically. During start-up, condensation, which is normal, forms on the inside of the glass and causes lint, dust and other airborne particles to cling to the glass surface. Also initial paint curing may deposit a slight film on the glass. It is therefore recommended that the glass be cleaned two or three times with a non-ammonia household cleaner and warm water (we recommend gas fireplace glass cleaner). After that the glass should be cleaned two or three times during each heating season depending on the circumstances present. Clean glass after first two weeks of operation. Glass Replacement Replace glass only with CFM Specialty Home Products approved parts. Refer to Page 35 for Replacement Parts. Refer to Figure 63 and previous instructions for removal of the damaged glass frame. ST139 Fig. 62 Remove the Stove Front. 20004188 33 3434 Radiance Direct Vent/Natural Vent Gas Heater 20004188 Gasket Replacement The Radiance Gas Heater uses a ‘tadpole’ type gasket to seal between the glass panel and the frame. In time, this gasket can become brittle and compressed and should be replaced. New gasket is available from your dealer. Shut off the gas supply and allow the stove to cool. Wear safety goggles and a dust mask. 1. Remove the Front, Glass Frame and Glass Panel. (Figs. 62 & 63) Remove the old gasket. Use a razor blade to separate the glass and gasket from the frame, and to clean the glass of any remaining cement or bits of gasket. Use a cold chisel if necessary. 2. Determine the correct length of gasket by laying it out around the edge of the glass. Allow an extra 1 - 2” (25-50mm). Mark the spot to be cut. Use a utility knife. 3. Starting on a long edge, remove about 6” of the protective paper strip and apply the flat adhesive face of the gasket around the outside-facing edge of the panel. Continue around the panel, applying a bout 6” at a time and being careful to not stretch the material. Do not overlap the gasket ends. (Fig. 64) 4. Apply a thin bead of high temperature silicone rubber sealant along the inside corner of the glass frame, all around the perimeter. Place the flat gasketed side of the glass panel back into the steel frame. Pinch the rounded inside-facing gasket material to bulk it up. 5. Replace the glass frame and front panel as previously described. Inspect the Vent System Annually Have the vent system inspected annually by a qualified technician. Shut off the main gas supply before inspecting the system. Both the inner exhaust pipe and the outer combustion supply pipe must be checked to confirm that they are unblocked and in good condition. Check the Gas Flame Regularly To ensure that the stove is operating properly, check the flames periodically to confirm that they match Figure 65. The flames will be blue during the first 15-20 minutes of operation, and will gradually turn to yellow after that. Do not use your stove if the flame pattern differs from that shown here. Contact your Vermont Castings dealer or a qualified technician for help. ST179 glass gasket detail 11/99 ST179 Fig. 64 Wrap the gasket material around the outside edge of the glass. LG157.. Radiance logs flame 4/24/01 djt Fig. 65 Correct flame pattern. LG157 Red Glow ST141 Fig. 63 Release the latches to remove the glass frame. ST141.. pull glass latch.. 10/99 Radiance Direct Vent /Natural Vent Gas Heater Wiring Diagrams On/Off Switch Wiring OFF ON .. ThermopileBlack Black TP/TH TP TH ST124b Optional Thermostat Wiring Thermostat (Optional) ThermopileBlack Black TP/TH TP TH ST124c Fig. 66 On/off switch and optional thermostat circuit. NOTE: IF ANY OF THE ORIGINAL WIRE, AS SUPPLIED WITH THE APPLIANCE, MUST BE REPLACED, IT MUST BE REPLACED WITH TYPE SF-2, 200°C WIRE OR ITS EQUIVALENT. Draft Hood TH TP TH TP Vent Safety Switch Gas Valve FAN JUNCTION BOX FAN POWER CORD Strain Relief Chassis Ground BLK GRN GRN WHT ON / OFFRheostat Chassis Ground RHEOSTAT / SNAPSTATBOX Snapstat BLKBLK BLK BLKBLK WHT ST153 MOTOR SNAPSTAT ON/OFFRHEOSTAT WHT WHT BLKBLKBLK GRN BLK Schematic Diagram ST236 ST359 Fig. 68 Fan circuit. Fig. 67 Draft Hood A dapter (FSDHAG) wiring. Used on RN/RP models only. 20004188 35 3636 Radiance Direct Vent/Natural Vent Gas Heater 20004188 46 1a 1b 1c PILOT ON OFF PILOT ADJ LO HI CEMENT 2 3 6 8 7 5 34 4 35 4188 RDVOD parts 6/11/01 djt 32 33 29a,b, c,d 9 30 LOCAL REMOTE ON• PILOT •OFF LED 23 24 25 7 10a,b 11a,b 12a 12b 12c 13 14 15 16 18 17 19 20a,b 22 21a,b 31 27 26 36 38 45 39 37 41 44 47 48 28 49 50 51 53 5...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: