Оценок - 3, средний балл: 4 ( )

Производитель: Vermont Casting Размер: 1.74 mb Название файла: Язык инструкции:

Vertical Termination, Flat Roof 7DVSKVF (1) Flat Flashing and all of the other Vertical Termination parts. Twist Lock 12” Straight Pipe (CG) 7TFSDVP12 (1) 12” Non-adjustable Pipe Twist Lock 12” - 18” Adjustable Pipe 7TFSDVP1218 (1) 12” - 18” Adjustable Pipe Twist Lock 24” Straight Pipe (CG) 7TFSDVP24 (1) 24” Non-adjustable Pipe Twist Lock 48” Straight Pipe (CG) 7TFSDVP48 (1) 48” Nonadjustable Pipe Twist Lock 45-Degree Elbow (CG) 7TFSDVT45 for vertical offsets (1) 45-degree Elbow Draft Hood Adapter FSDHAG NV Stove Kit 7FSSK (1) 7” Diameter Polished Brass Trim Ring (1) 48” Nonadjustable Pipe (CG) (1) 24” Nonadjustable Pipe (CG) (1) Finishing Plate (1) Finishing Collar (CG) (1) 90 Degree Elbow (CG) Stove Kit 7FSDHASK Includes all parts in the 7FSSK plus the Draft Hood Adapter FSDHAG Combination Offset/Roof Support 7DVCS Attic Insulation Shield 7DVAIS 7” Charcoal Gray Pipe Rings, (4) 7FSDRG 7” Polished Brass Pipe Rings (4) 7FSDRP Wall Thimble 942G NOTE: Direct vent pipe may be used on the Natural Vent system from the top of the draft hood adapter to the ceiling. Radiance Direct Vent /Natural Vent Gas Heater ST720 Fig. 12 Slide stove back just far enough to access rear leg holes. Assembly Procedures Failure to position the parts in accor- dance with these diagrams or failure to use only parts specifically approved for use with this heater may result in property dam- age or personal injury. This heater and components are heavy. Have help available for assembly. WARNING Tools Required • Phillips screwdriver (stub) • power drill • utility knife • reciprocating saw • metal drill bit: size 28 (.140”/3.5mm) Parts Bag Contents: • Control door handle/screw • (3) Vent Screws • (2) Switch bracket screws • Ceramic handle w/insert lifter (handle for operable door) • On-Off switch, housing, and wiring harness (3) Phillips round-head bolts, 1/4”- 20 x 1/2” • (2) Bag of Lava Rocks • (1) Tube of Vent Gasket Cement • (1) Vent Restrictor Plate, 2..." inside diameter • Owner Registration Card • (4) CS, Hex Hd 3/8-16 x 1 Gr 2-Z • (4) Washer, Fl 3/8-Z Unpack and Assemble Legs The Radiance is shipped upright. Cut the shipping straps and set stove upright. 1. Slide stove to the rear of the pallet just far enough to access rear leg holes. Make sure the stove does not tip over backwards. (Fig. 12) 2. Attach the rear legs using 3/8” hex head bolts and flat washer supplied. Tighten with a 9/16” wrench or socket. 3. Carefully tip the stove onto its rear legs. Adjust the pallet to allow access to one of the front leg holes. Be sure to leave the pallet under the stove to prevent the stove from falling fully forward. (Fig. 13) CAUTION: To prevent valve tubing from being crushed or damaged, make sure to rest valve on wooden pallet. 4. Have your assistant attach one leg using the hardware described. 5. Move the pallet to allow access to the other front leg hole. Attach remaining leg. Washer Hex Head Bolt Fig. 13 Carefully tip stove onto back legs. Leave pallet under stove to keep stove from falling fully forward. 6. Remove pallet and allow stove to gently rest on all four legs. 7. Adjust leg levelers to compensate for irregularities in the hearth. NOTE: Verify the two relief doors (located on top of the firebox) are properly seated on the gasket. The doors should sit flush on the gasket, and should lift easily from the seal around the opening. 20004188 13 1414 Radiance Direct Vent/Natural Vent Gas Heater 20004188 ST347a JUV FK28 rheostat install 9/21/00 Rheostat Retaining Collar Rheostat Knob ST347a Fig. 17 Attach the fan rheostat. Rheostat Install the Optional Fan If you are installing the optional convection Fan Kit #2767 (FK26), continue here. It is easiest to install fan kit before connecting gas line. If you are not installing a Fan Kit, go to Page 15, Venting System Assembly. 1. The fan kit includes a Blower Assembly and a Rheostat Assembly, connected by a cable. (Fig. 14) The Blower Assembly mounts to the bottom rear of the stove, and the Rheostat mounts to the valve coverplate. The assembly includes a ‘snapstat’ which automatically turns the fan On (or Off) above (or below) approximately 109.. The Rheostat also provides a range of fan speed settings from Off (which overrides the snapstat function) to High. Unpack and inspect the Blower assembly. Confirm that the fan spins freely. ST147.. RDV40 remove rear shroud 10/99 Fig. 15 Remove rear shroud. ST147 ST473 Fan parts #2767 FK26 9/29/00 Not Used On Radiance Snapstat Bracket Snapstat/ Extension Assembly Rheostat Assembly ST473 Blower Assembly Fig. 14 Fan kit components. Not Used On RF Models Not Used On RF Models Connect to PC board on RF models only WARNING This appliance is equipped with a three-prong (grounded) plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from this plug. 2. Remove the rear shroud panel (Fig. 15) and fasten the blower assembly to the firebox back wit...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: