M3618/1100(OM-40-C-HT) 1/25/02 3:36 PM Page 2 W h e re Do I Find Everything I Need for P rocess Measurement and Control? OMEGA…Of Course! Shop online at T E M P E R A T U R E Thermocouple, RTD & Thermistor Probes, Connectors, Panels & Assemblies Wire: Thermocouple, RTD & Thermistor Calibrators & Ice Point References Recorders, Controllers & Process Monitors Infrared Pyrometers PRESSURE, STRAIN AND FORCE Transducers & Strain Gages Load Cells & Pressure Gages Displacement Transducers Instrumentati

DMD-480-S2 SERIES HOOK-UP (REFER TO FIGURE 1 AND TABLE 1 FOR SCREW TERMINAL DESIGNATION) 1. CONNECT AC TO SCREW TERMINALS 5 AND 6 OF THE DMD-480-S2 SERIES TERMINAL BLOCK. 2. USING A ONE TO ONE DB9 CABLE, CONNECT ONE END TO YOUR COMPUTERS SERIAL PORT, (COM1 OR COM2 ONLY), AND THE OTHER END TO THE DMD-480-S2 SERIES FEMALE DB9 CONNECTOR. THE RECOMMENDED MAXIMUM CABLE LENGTH IS 50 FT. WHICH IS TABLE 1 DETERMINED BY THE MAXIMUM SPECIFIED CABLE CAPACITANCE FIGURE 1 OF 2500pF. 3. CONNECT THE STRAIN GAG

Combined with one of our pressure calibrators, the PPA100 makes a complete Pressure/ Vacuum Calibration System. Operation The drawing shows the operation of the controls on the PPA100. The pump is designed for use with ambient air only. Pump Valve Assembly Cleaning Instructions Occasionally, the PPA100 may not work properly due to dirt or other contamination of the internal valve assembly. Use the following procedure for cleaning the valve assembly. 1. Using a small screwdriver, remove the 2 val

Continuous Level Sensors should be installed rigidly so the float is free to move as the liquid level changes. 2. Continuous Level Sensors should be mounted in a tank area free of severe turbulence or protected from such turbulence by appropriate and adequate slosh shields. 3. Continuous Level Sensors stems should be vertical for best results, but satisfactory operation is possible in most liquids with the stem at up to a 30° angle from vertical. 4. Care should be taken that Continuous Level Sen

The sensor should be put in its normal operating position (vertical or horizontal). Remove the cover to gain access to the zero and span adjustment potentiometers. Zero adjustment uDepending on the model, set the zero adjustment to: 0.00 V, 4.00 mA or 12.00 mA. uSpan adjustment is carried out with the required span pressure applied to the + uDepending on the model, set the span adjustment to: 5.00 V, 10.00 V or 20.00 mA. uRelease the pressure. Completion Check the output at zero pressure and if

The sensor is compatible with a broad range of conductive and non-conductive liquids. It is also suitable for high, low or intermediate level detection in practically any tank - large or small. Installation is simple and quick through the tank top, bottom or side. With no moving parts, the sensor is ideal for interstitial applications. The pull ring facilitates easy installation in double-wall tanks and pipes, yet can be removed for use in 1/4" NPT holes. SENSOR SENSORSENSORSENSORSENSORSENSOR OP

10. Make sure heaters are installed and used by qualified personnel. DO NOT attempt to repair damaged heaters. OMEGAnet® Online Service Internet e-mail omega.com info@omega.com OMEGAnet® Online Service Internet e-mail omega.com info@omega.com Servicing North America: U.S.A.: One Omega Drive, Box 4047 ISO 9001 Certified Stamford, CT 06907-0047 Tel: (203) 359-1660 FAX: (203) 359-7700 e-mail: info@omega.com Canada: 976 Bergar Laval (Quebec) H7L 5A1, Canada Tel: (514) 856-6928 FAX: (514) 856-6886 e-

Wattage ratings are 2.5, 5, or 10 W/in2 at 115 or 28 volts. Kapton offers a high degree of resistance to chemicals, and has excellent outgasing properties in high vacuum environments. KH models are rectangular 115 volt units; KHLV models are rectangular 28 volt units, and KHR models are round 115 volt units. Contact OMEGA sales Department for specific part numbers: 800-872-9436 Typical construction consists of an etched foil element of 0.0005" or 0.0001" thickness, which is encapsulated between

Components in which wear is not warranted, include but are not limited to contact points, fuses, and triacs. OMEGA is pleased to offer suggestions on the use of its various products. However, OMEGA neither assumes responsibility for any omissions or errors nor assumes liability for any damages that result from the use of its products in accordance with information provided by OMEGA, either verbal or written. OMEGA warrants only that the parts manufactured by the company will be as specified and

ol: (001) 203-359-7803 e-mail: espanol@omega.com FAX: ( 001) 203-359-7807 info@omega.com.mx Servicing Europe: Benelux: Postbus 8034, 1180 LA Amstelveen, The Netherlands Tel: +31 (0)20 3472121 FAX: +31 (0)20 6434643 Toll Free in Benelux: 0800 0993344 e-mail: sales@omegaeng.nl Czech Republic: Frystatska 184, 733 01 Karvina, Czech Republic Tel: +420 (0)59 6311899 FAX: +420 (0)59 6311114 Toll Free: 0800-1-66342 e-mail: info@omegashop.cz France: 11, rue Jacques Cartier, 78280 Guyancourt, France Tel: