Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
DMD-480-S2 SERIES HOOK-UP (REFER TO FIGURE 1 AND TABLE 1 FOR SCREW TERMINAL DESIGNATION) 1. CONNECT AC TO SCREW TERMINALS 5 AND 6 OF THE DMD-480-S2 SERIES TERMINAL BLOCK. 2. USING A ONE TO ONE DB9 CABLE, CONNECT ONE END TO YOUR COMPUTERS SERIAL PORT, (COM1 OR COM2 ONLY), AND THE OTHER END TO THE DMD-480-S2 SERIES FEMALE DB9 CONNECTOR. THE RECOMMENDED MAXIMUM CABLE LENGTH IS 50 FT. WHICH IS TABLE 1 DETERMINED BY THE MAXIMUM SPECIFIED CABLE CAPACITANCE FIGURE 1 OF 2500pF. 3. CONNECT THE STRAIN GAGE OUTPUT TO THE DMD-480 SERIES ± INPUT, TERMINALS 1 AND 2 OF THE DMD-480-S2 SERIES TERMINAL BLOCK. TERMINAL 1= +INPUT, TERMINAL 2= -INPUT. 4. CONNECT THE STRAIN GAGE +EXCITATION INPUT TO THE DMD-480 SERIES TERMINAL BLOCK, TERMINAL 4, AND THE STRAIN GAGE EXCITATION INPUT TO TERMINAL 3. DMD-480-S2 Series Block Diagram TERMINAL FUNCTION 1 +INPUT 2 -INPUT 3 -EXCITATION 4 +EXCITATION 5 AC 6 AC One Omega Drive, P.O. Box 4047 Stamford, CT 06907 DMD-480-S2 SERIES AC POWERED BRIDGESENSOR - RS232 INTERFACE DMD-480-S2 SERIES AC POWERED BRIDGESENSOR - RS232 INTERFACE ADDRESS 63ADDRESS 21BINARY = 100000DECIMAL = 1 + 0 + 0 + 0 + 0 + 0 = 1ADDRESS 1BINARY = 111111DECIMAL = 1 + 2 + 4 + 8 + 16 + 32 = 63 TABLE 3: ADDRESS EXAMPLE. B. DMD-480-S2 SERIES DIP SWITCH SETTINGS 1. SET THE DESIRED ADDRESS FOR EACH UNIT BY SETTING SWITCHES 1-6. BY SETTING THIS ADDRESS, THE UNIT IS GIVEN ITS OWN IDENTITY TO WHICH THE HOST COMPUTER WILL IDENTIFY WITH. • THE ADDRESS RANGE IS FROM 0 - 63 (DECIMAL) OR 111111 (BINARY). (REFER TO EXAMPLES IN TABLE 3). • SWITCH “ON” = 0; SWITCH “OFF” = 1 2. SET THE DESIRED MODE OF OPERATION FOR THE 4570-232 USING SWITCHES 7 & 8. (REFER TO TABLE 2 FOR DEFINING MODES OF OPERATIONS) MODE 3 IS USED FOR DIAGNOSTIC PURPOSES. TABLE 2. SW 7 SW 8 MODE DESCRIPTION ON ON 0 OPERATE MODE: Operate Mode: Unit Outputs a reading whenever it is addressed by the the host computer. OFF ON 1 TEST MODE: Unit outputs a reading every 0.33 seconds continuously without being addressed ON OFF 2 UNDEFINED: OFF OFF 3 TEST MODE: Unit outputs a message " MODE 3: Version: 941124 Address: 01" continuously. BINARY = 10101. DECIMAL = 1 + 0 + 4 + 0 + 16 + 0 = 2. C. SOFTWARE INSTALLATION SWITCH DECIMAL VALUE 1 1 2 2 3 4 4 8 5 16 6 32 THE SUPPLIED OMEGA SOFTWARE, C4500.BAS, IS INTENDED FOR USER MODIFICATION. PLEASE FEEL FREE TO MAKE ANY CUSTOM MODIFICATIONS TO THE SOFTWARE AS NEEDED. IT IS RECOMMENDED THAT THE USER MAKE A BACKUP COPY OF THE ORIGINAL OMEGA SOFTWARE BEFORE MODIFYING. 1. TO EXECUTE THE OMEGA C4500 SOFTWARE, QBASIC OR GWBASIC MUST BE LOADED ON YOUR COMPUTER. 2. TO BEGIN THE SOFTWARE SETUP, YOU MUST LOAD AND EXECUTE THE SUPPLIED OMEGA PROGRAM, “C4500.BAS” WITHIN QBASIC OR GWBASIC. D. SETUP MENU THE FIRST MENU TO APPEAR IS THE “SETUP MENU” IF YOU WANT TO SAVE ANY SETTINGS WHICH WILL BE ENTERED INTO THE PROGRAM, YOU WILL WANT TO ENTER THOSE SETTINGS DIRECTLY INTO THE SOFTWARE AND SAVE THE SOFTWARE WITH AN APPLICATION NAME (XXXXX.BAS). AFTER YOU QUIT THE OPERATION MENU OR TURN OFF THE HOST COMPUTER, ALL SETTINGS WILL RETURN TO THEIR DEFAULT VALUES UNLESS SAVED. PHONE:(203)359-1660 FAX:(203)359-7700 1-800-TC OMEGA info@omega.com DMD-480-S2 SERIES AC POWERED BRIDGESENSOR - RS232 INTERFACE DMD-480-S2 SERIES AC POWERED BRIDGESENSOR - RS232 INTERFACE THE SETUP MENU ALLOWS THE USER TO SETUP THE CORRECT OPERATING PARAMETERS FOR THE DMD-480-S2 SERIES. 1. OPTION 0 [RETURN TO OPERATION MENU]: SELECTING THIS OPTION WILL RETURN YOU TO THE OPERATION MENU. 2. OPTION 1 [SELECT COMMUNICATIONS PORT]: THIS OPTION ALLOWS THE SELECTION OF EITHER COM1 OR COM2 AS THE COMMUNICATIONS PORT FOR THE DMD-480-S2 SERIES AND THE USERS COMPUTER. COM3 AND COM4 ARE NOT ALLOWED. THE SETTING OF THE COMMUNICATIONS PORT IS ALWAYS NECESSARY FOR PROPER OPERATION OF THE DMD-480-S2 SERIES IN BOTH THE OPERATION AND TEST MODES. 3. OPTION 2 [SET SCALING EQUATION]: THIS OPTION ALLOWS THE USER TO SELECT COEFFICIENTS OF A SCALING EQUATION. THE SCALING EQUATION PROVIDES FOR BOTH A SCALE FACTOR (A) AND A FIXED OFFSET (C). THE SCALING EQUATION IS: VALUE = C + (A x READING) THE SETTING OF THE SCALING EQUATION ONLY APPLIES TO THE “OPERATION MODE”. (REFER TO SECTION F FOR A DESCRIPTION ON SETTING THE SCALING EQUATION.) 4. OPTION 3 [SELECT DATA DESTINATION]: THIS OPTION ALLOWS THE USER TO STORE DATA IN ONE OF 3 MODES. THE DATA MAY BE DISPLAYED ON THE COMPUTER SCREEN ONLY, SENT TO A FILE ONLY, OR BOTH. THIS OPTION APPLIES ONLY TO THE “OPERATION MODE”. (REFER TO SECTION G FOR MORE INFORMATION ON STORING DATA.) 5. OPTION 4 [DATA COLLECTION METHOD]: THIS OPTION ALLOWS THE USER TO COLLECT DATA IN 3 DIFFERENT WAYS AND ONLY APPLIES TO THE OPERATE MODE, NOT THE TEST MODE. 1) TAKE A READING EVERY “Y” SECONDS, WHERE “Y” IS ONE SECOND MINIMUM, FOR A TOTAL “A” MINUTES. 2) START TAKING DATA EVERY “Y” SECONDS AT TIME “A” UNTIL TIME “B”. 3) TAKE DATA EVERY “Y” SECONDS STARTING NOW AND CONTINUE READING DATA FOREVER. THIS IS THE DEFAULT METHOD FOR THE OPERATE MODE. BY DEFAULT, THE VALUE FOR “Y” MUS...