2. Connect POL fitting on hose/regulator assembly to propane tank(s). Turn POL fitting counterclockwise into threads on tank. Tighten firmly using 7/8" wrench. IMPORTANT:Tighten regulator with vent pointing down. Pointing vent down protects regulator from weather damage. Supply Valve Propane Tank POL Fitting Hose Regulator Vent (pointing down) Figure 2 - Regulator With Vent Pointing Down 3. Connect hose to the inlet connector. Tighten firmly using 9/16" wrench. IMPORTANT:Use extra hose or piping

Pointing vent down protects regulator from weather damage. Figure 3 - Regulator With Vent Pointing Down Continued Hose Regulator Vent (pointing down) POL Fitting Supply Valve Propane Tank 3. Connect hose to inlet connector. Tighten firmly using a wrench. IMPORTANT:Extra hose or piping may be used if needed. Install extra hose or piping between hose/regulator assembly and propane tank. You must use the regulator supplied with heater. 4. Open propane supply valve on propane tank(s) slowly. Note:If

If a leak occurs, propane gas will sink to the lowest possible level. • Keep appliance area clear and free from combustible materials, gasoline, paint thinner, and other flammable vapors and liquids. Do not use heater in areas with high dust content. • Minimum heater clearances from combustibles: Outlet: 8 Ft. Sides: 2 Ft. Top: 6 Ft. Rear: 2 Ft. • Keep heater at least six feet from propane tank(s). Do not point heater at propane tank(s) within 20 feet. • Keep propane tank(s) below 100° F. • Chec

WARNING: Proper shoulder strap and handlebar adjustments must be made with the engine completely stopped before using unit. The shoulder strap clamp must be installed as shown above the handlebar on the upper shaft (powerhead end of unit). NOTE: The lower shoulder strap clamp has two spacer tabs attached. These tabs are provided to adapt this attachment for use with powerheads that have a 1. (2.5 cm) diameter upper shaft (the shoulder strap clamp will not tighten down securely on the 1. (2.5 cm)

CHECK FOR DAMAGED OR WORN PARTS Contact an authorized service dealer for replacement of damaged or worn parts. S Blade Shield - --Discontinue use of brushcut ter attachment if shield is damaged. CHECK FOR LOOSE FASTENERS AND PARTS S Blade nut S Fasteners INSPECT AND CLEAN UNIT AND DECALS S After each use, inspect complete unit for loose or damaged parts. Clean the unit and decals using a damp cloth with a mild detergent. S Wipe off unit with a clean dry cloth. BLADE MAINTENANCE WARNING: The blad

IF YOU NEED ASSISTANCE OR HEATER INFORMATION SUCH AS AN INSTRUCTIONS MANUAL, LABELS, ETC. CONTACT THE MANUFACTURER. ® FIRST EDITION PART NO. 18994 Printed In U.S.A. Price $1.00 SECTION PAGE CONTENTS Safety Information ......................................................................... 2 Product Identification .................................................................... 4 Unpacking...................................................................................... 4 Theory of Oper

shaft S Handlebar mounting bracket for 7/8. shaft S Bracket cover (2) S Shoulder strap S Upper shoulder strap clamp S Lower shoulder strap clamp (with spacer tabs) S Handlebar bracket screws (4) S Shoulder strap clamp screws (2) S 4- --point weed blade (assembled on brush- cutter attachment) S Large nut for installing blade S Retaining washer S Cupped washer S Metal shield (assembled on brushcutter at tachment) S Trimmer head S Plastic shield S Wing nut (screwed onto plastic shield) S Attachment

No. 236 Assembly Instructions § Parts List DUMP CART No. LM-16002-36 Assembly 1. Mount the two wheel and tire assemblies on the axle and secure with two 3/4" washers and two 3/16 x 1-1/2" cotter pins. 2. Mount the frame assembly to the axle assembly and secure with two 5/16 x 4-5/8 L-shaped pins and two quick pins. Be sure the axle curve is away from the ground. 3. Bolt the tongue to the frame assembly using two 3/8-16 x 2-1/4" caps crews, lockwashers, and hex nuts. Be sure that the fron

UT34020 Your new pole pruner has been engineered and manufactured to Homelite’s high standard for dependability, ease of operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injur y, the user must read and understand the operator’s manual before using this product. Pay close attention to the Rules for Safe Operation, Warnings, and Cautions. If you use your pole pruner properly and only for what it is intend

MC-6066-211501 OIL TENK 1 50 MC-6038-211506 HOUSING (L) 16 MC-6028-211502 TRIGGER 1 51 MC-6086-211501 REAL COVER 1 17 MC-6022-211502 SWITCH 1 52 MC-6228-211301 MOTOR GEAR BOX ASS'Y 18 MC-6024-211301 SPRING 1 53 MC-6022-211501 SWITCH 1 19 MC-6CY-08 RING 1 54 MC-6SDABB04-10 SCREW 20 MC-6079-211501 SPRING, BRAKE 1 55 MC-6011-211502 POWER CORD 1 21 MC-6073-211501 GEAR 1 56 MC-6043-840001 STRAIN RELIEF 22 MC-6059-210201 ADJUSTMENT COVER 1 57 MC-6059-855001 CORD GUARD 1 23