You will hear a click as the clips engage. 3. Fully push the drawer into the case. Global Machinery Company 16 Scammel Street, Campbellfield Victoria, Australia 3061 Tel: (03) 9303 2133 Fax: (03) 9308 7822 Customer Helpline 1300 880 001 (Australia) 0800 445 721 (New Zealand) 300PCE 030117 300PCE EDS

Firing speed Max. Length of nail Max. Magazine Capacity 230-240 Volts 50 Hz 20-Nail-per minute Up to 32mm long (drives five lengths) Holds up to 100 nails DIRECTIONS FOR USE Step one: Loading your Master Nailer 1. Unplug from power source. 2. Only use nails recommended. 3. Slide the pusher backwards from position B to position A by levering the catch (1) backwards. 4. Load selected nails (nail points facing downwards) into the track of magazine (2). 5. Head of nail can go above and below

Use of the power tool for operations different from intended could result in a hazardous situation. Service • Have your power tool serviced by a qualified repair personnel using only identical replacement parts. • When operating a power tool outdoors, use an outdoor extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. This will ensure that the safety of the power tool is maintained. Additional safety instructions for engravers • Alwa

A power source with a voltage greater than that specified for the tool can result in serious injury to the user, as well as damage to the tool. If in doubt, do not plug in the tool. Using a power source with a voltage less than the nameplate rating is harmful to the motor. Switch on WARNING. The gun will continue to heat up when the trigger (4) is pressed in. To extend the life of the gun, do not press the switch for long time. 1. Ensure that both tip release screws (2) are tight and the solderi

• Damage to eyes if effective goggles are not worn • Risk of injury unless hands are kept well clear of cutting devises Unpacking Due to modern mass production techniques, it is unlikely that your GMC Power Tool is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury. Operation WARNING. Before connecting a tool to a power source, be sure th

Wear goggles, Wear earmuffs Wear a breathing mask The tool must be used only for its prescribed purpose. Any use other than those mentioned in this Manual will be considered a case of misuse. The user and not the manufacturer shall be liable for any damage or injury resulting from such cases of misuse. The manufacturer shall not be liable for any changes made to the tool nor for any damage resulting from such changes. Even when the tool is used as prescribed it is not possible to eliminate all r

A combination of Carbon Fibre and Magnesium construction offers the very latest in manufacturing materials that maximise strength and durability in a lighter powertool. An increased range of applications are made possible by the 3 modes of operation including Non Impact drilling, Impact Drilling and Stop Rotationwhich is used for chiselling to remove tiles and the breaking up of concrete. SDS Plus bit fitment provides for a reliable and fast method of fitting your accessories while safety featur

Accessories The GMC DEC005GG comprises the following components: 1 x Instruction manual 10 x Glue sticks (150mm x O11mm) Operation WARNING. Before connecting a tool to a power source, be sure that the voltage supply is the same as that specified on the nameplate of the tool. A power source with a voltage greater than that specified for the tool can result in serious injury to the user, as well as damage to the tool. If in doubt, do not plug in the tool. Using a power source with a voltage less t

Keep your footing secure and balanced at all times. 12. Look after your tools. Keep tools sharp and clean for better and safer performance. Follow the instructions regarding lubrication and accessory changes. Inspect tool cords periodically and, if damaged, have them repaired by an authorised service facility. Inspect extension cords periodically and replace them if damaged. Keep tool handles dry, clean and free from oil and grease. 13. Disconnect idle tools. Switch off the power and disconnect