To facilitate cutting, a Banner model PFC-1 cutting device is supplied with this fiber. Cut the fiber as follows: 1) Locate the "control end" of the fiber (the unfinished end). Determine the length of fiber required for the application. At the control end of the fiber, separate the two fibers. Lift the top (blade) of the cutter to open the cutting ports. Insert one of the control ends through one of the two small cutting ports on the PFC-1 cutter so that the excess fiber protrudes from the back

Temperatures above +70°C will cause both transmission loss and fiber shrinkage. REPEAT BENDING/FLEXING: Life expectancy of plastic fiber optic cable is in excess of one million cycles at bend radii of no less than the minimum (stated at right) and a bend of 90 degrees or less. Avoid stress at the point where the cable enters the sensor ("control end") and at the sensing end tip. Coiled plastic fiberoptic assemblies are recommended for any application requiring reciprocating fiber motion. OPERATI

Cut the fiber as follows: 1) Locate the "control end" of the fiber (the unfinished end). Determine the length of fiber required for the application. At the control end of the fiber, separate the two fibers. Lift the top (blade) of the cutter to open the cutting ports. Insert one of the control ends through one of the four large cutting ports on the PFC-2 cutter so that the excess fiber protrudes from the back of the cutter. 2) Double-check the fiber length, and close the cutter until the fiber i

To facilitate cutting, a Banner model PFC-1 cutting device is supplied with this fiber. Cut the fiber as follows: 1) Locate the "control end" of the fiber (the unfinished end). Determine the length of fiber required for the application. At the control end of the fiber, separate the two fibers. Lift the top (blade) of the cutter to open the cutting ports. Insert one of the control ends through one of the four large cutting ports on the PFC-1 cutter so that the excess fiber protrudes from the back

It is ideal for right-angle sensing in "tight" areas. The PBPS26U operates in the diffuse sensing mode. Sensing light is transmitted and received through an opening located in the side of the sensing probe near the tip (see drawing and photo). Objects are detected by the light they reflect back through the opening. Fiber core diameter is .02 inch. NOTE: The probe tip is non-bendable. The PBPS26U may be used with plastic fiber optic sensors from the following Banner sensor families: D12, OMNI-BEA

A Geometric Find tool compensates for positional variation. ▲ Complete Case Inspection The PresencePLUS P4 GEO 1.3 verifies the correct assembly of product bottles in a case. The Find Locating tool and Count Inspecting tool recognise patterns in any orientation up to 360°. Banner Engineering offers the industry a highly complete and integrated line of photoelectric sensors, ultrasonic sensors, machine safety products, measurement & inspection products and vision sensors. Banner Engineering i

Q12 Miniature Sensor • Rated IP67 for use in the widest range of locations and applications Overmoulded design provides enhanced durability and shielding • Robust metal-lined mounts with standardised location on all models • Powerful sensors suitable for extremely confined areas • Opposed, retro-reflective (polarised & non-polarised) and fixed-field sensing modes • Precise cutoff backgroundsuppression available in three fixed-field models • Mounting flexibility directly on and inside man

DUO-TOUCH Two-Hand- Control Prevent repetitive stress injuries • Dependable switching with no physical pressure required • Eliminate hand, wrist and arm stress • Ergonomically designed for use with repetitive operations • Designed to comply with Category 4 per ISO 138491 (EN 954-1); Type IIIC per ISO 13851 (EN 574) • Ease of installation • Productivity improvement • I deal solution for punch presses and others dangerous machines more sensors, more solutions Banner Engineering Europe

If the stopper is incorrectly positioned or if the vial is under filled, a FAIL output is sent from the vision sensor to the filling machine. ▲ Bottle Label Alignment The P4 EDGE measures the horizontal displacement between the labels and verifies that each individual label is applied straight and not skewed. ▲ Syringe Assembly Verification The P4 EDGE checks for the presence of a needle and verifies that it is straight. It also measures the epoxy glue for over- or under-fill. Banner Engine

sensor • Complete range • High performance • Competitive price • Easy installation • Easy diagnostics • Resistant to harsh environments • M12 connector • Many accessories • Easy set-up A universal sensor with simplified set-up! QS18 photoelectric Easy set-up • Potentiometer or Teach Function for Expert version • Easy adjustment featuring a specially moulded stop which prevents over-adjustment damage; no extra tools needed Easy diagnostics • Bright LED operating status indicator