The VMCC1 is designed to mount a center channel speaker below a Sanus VMSA, VMAA, VMAA18, VMAA26, VMDD or a VMDD26 Flat Panel Wall Mount. Safety Warning: If you do not understand these directions, or have any doubts about the safety of the installation, please call a qualified contractor or contact Sanus at 800.359.5520 or Check carefully to make sure that there are no missing or defective parts. Our customer service representatives can quickly assist you with installation questions and missing

3. PITCH-justering Lossa lasskruven for PITCH-justering med en #2 Phillips-skruvmejsel. Vrid mikrojusteringsskruven for PITCH at hoger eller vanster med en #2 Phillips-skruvmejsel tills bilden ar inriktad pa malet. Dra at lasskruven for PITCH-justering med en #2 Phillips-skruvmejsel. 6901-002053 <00> Русский ПРЕДУПРЕЖДЕНИЕ! ВАЖНЫЕ ИНСТРУКЦИИ ПО ТЕХНИКЕ БЕЗОПАСНОСТИ – СОХРАНИТЕ ЭТИ ИНСТРУКЦИИ – ПЕРЕД ЭКСПЛУАТАЦИЕЙ ИЗДЕЛИЯ ПОЛНОСТЬЮ ПРОЧТИТЕ ДАННОЕ РУКОВОДСТВО Технические характеристики • Нагрузка

6901-002026 <02> 6901-002026 <02> 7 M8 x 40mm M4 x 30mm M6 x 35mm M5 x 30mm M4 / M5 M6 / M8 M4 / M5 M6 / M8 1/4 x 2.0 in. 1/4 in. 1/4-20 #10 x 1 in. 1/4-20 [08] x 2 [09] x 2 [10] x 2 [11] x 2 [12] x 2 [13] x 2 [14] x 2 [15] x 2 [04] x 2 [05] x 1 [06] x 1 [07] x 1 [01] x 1 [02] x 1 [03] x 2 8 6901-002026 <02> 1 CAUTION: Attach TV Supports (T) to TV 1. Hand thread screws into the threaded inserts on the back of your TV to determine the correct screw diameter (M4, M5, M6, or M8). 2. Attach TV suppo

The VMCA9 ceiling plate is designed to attach to an NPT 1-1/2 in. threaded pipe. The VMCA9 will support a maximum weight of 226.8 kg (500 lbs). - CAUTION - Do not use this product for any purpose not explicitly specified by Sanus Systems. Improper assembly may cause property damage or personal injury. If you do not understand these directions, or have doubts about the safety of the assembly, contact Sanus Systems Customer Service or call a qualified contractor. Sanus Systems is not liable for

If you have any questions regarding this or any other Sanus product, please contact our customer service department at (800)359-5520, or It is not necessary to contact the retailer with any questions or problems, as parts can be sent directly to you. Please follow these assembly instructions. This will save you time, make assembly easier and prevent possible damage to your new Digital TV Stand. Assistance may be required for some assembly procedures. Correct assembly is your responsibility. BU

It can also be used with a VM200 for tilting LCDs or a VMPL50 for Plasmas. Safety Warning: If you do not understand these directions, or have any doubts about the safety of the installation, please call a qualified contractor or contact Sanus at 800.359.5520 or Check carefully to make sure that there are no missing or defective parts. Our customer service representatives can quickly assist you with installation questions and missing or damaged parts. Replacement parts for products purchased thro

When Using the TV27 or TV32 use the rear Pilot Hole. Step 3: Insert the Plastic Dowels into the larger holes in the Support Pillar as shown in the Diagram on the right. Gently tap the Plas- tic Dowels in with a hammer if needed. Repeat step for the other Support Pillar. Step 4: Thread the Allen Bolts up through the Base of the TV-VCR Kit, and into the corresponding holes in the Support Pillar. Tighten Allen Bolts with the provided Allen Key until they are tight. Step 5: Add the TV Turntable to t

Paul, MN 55113 800.359.5520 7.6.04 TVTurntable (sold separate) SupportPillar SupportPillar SupportPillar SupportPillar SupportPillar SupportPillar SupportPillar SupportPillar SupportPillar SupportPillar Support PillarPillarPillarPillarPillarPillarPillarPillarPillarPillarPillarPillarPillarPillarPillar BaseBaseBaseBaseBaseBaseTV Turntable (sold separate) Pillar SupportPillar SupportPillar Support Base Step 1: Remove the swivel from the TV Turntable by removing the Phillips Screw in the center of t

Please check carefully to make sure there are no miss- ing or defective parts. Never use defective parts. Improper assembly may cause damage or injury. If you do not understand these directions, or have any questions about this assembly please contact Sanus at 800.359.5520 or We can quickly assist you with installation questions and missing or damaged parts. Supplied Parts: (1) Television Turntable Supplied Parts: (1) Self Adhesive Protective Feet (pad of 4) Diagram 1Step 1: Position the Turntab