1 8 Standard Timer Controls 6.2 9 Recipe Timer Controls 6.2 10 Bowl Placement 6.3 11 Agitator 6.4 11 Prepare for Mixing 6.5 12 Operating Notes 6.6 12 Standard Timer Operation 6.7 12 Recipe Timer Operation 6.7 14 View Recipe 6.7 15 Programming Recipe Timer 6.7 15 Unloading 6.8 17 Guard Wire Cage 6.9 17 Remove and Cleaning the Guard Wire Cage 6.10 18 Re-Fitting the Guard Wire Cage 6.11 18 Mixing Capacity Chart 6.12 19 Agitators and Attachments 6.13 21 2 Using the Attachment Facility Using the Atta

3. Lower the front of the wire cage and move the wire cage slightly to the rear so the rear retainer shoes clear the ridge of the drip cup. The wire cage can now be removed. Fig. 6 4. Wash the wire cage in a sink, rinse with clear water, and dry with a clean cloth. 5. The stainless steel splash guard can be wiped off and/or washed with a cloth or sponge using warm, soapy water. Rinse with clear water and dry with a clean cloth. Reinstall Wire Cage 1. Position the ring of the wire cage so the fro

Buzzer sounds and display will show recipe number that was programmed with the number blinking. 13.Press PGM to enter run mode. (Buzzer sounds) 14.Press STD to return to standard mode or set recipe selector to the desired recipe. 15.Select the recipe that you programmed and verify proper operation. UNLOADING1.Openthe bowl guard wirecageassembly. 2.Lower bowl support. 3.Removethe agitator from the agitatorshaft. 4. Slightlyliftthe bowloff thepin (rightside),pullbowl to the frontand removefrom the

2TABLE OF CONTENTS GENERAL...............................................................................................3 INSTALLATION...............................................................................................3 Unpacking.............................................................................................3 Location................................................................................................3 Electrical Connections....................................

The Legacy 20-quart mixer is a bench-type mixer which features a SmartTimer™, a manual bowl lift and a #12 attachment hub as standard equipment. With the use of special agitators, a 12 quart bowl may be used on the HL200 mixer. A variety of attachments, agitators and accessories are available. These are described in a separateUse and Applications Handbook, which is furnished on the Legacy Mixer Operator Training CD provided with each mixer. INSTALLATIONUNPACKING Immediately after unpacking the m

c.If the timeischanged while mixing,the mixerwill operate until the new time expires. The adjustment to the timewillnot be stored. d. If speedis changed whilemixing, the time will change to the previous time for theselected speed and count down. NOTE:If the wire cage is opened at any time, the mixing operationwill stop. To resume the mixingoperation, close the wire cage andpress theSTARTbutton. 3. Whenthe timer reaches 00:00, themixerstops;a beeper sounds for 1 second.The count- down timer then

5. When the timer reaches the end of the last programmed recipe step, the mixer stops; the beeper sounds; the selected recipe is displayed. View Recipe When the mixer is in RECIPE mode, you can view the step settings of any recipe. 1. Press the SELECT/SAVE button. A. Display will alternate between speed and time. B. The LED of the step being displayed will flash. 2. Use the arrow buttons to view the next step. 3. Use the Recipe selector to view other recipes. 4. Press PGM button to return to the

controls ML-126456 ML-126728 HR7 auto. controls ML-126455 ML-126725 prog. controls ML-126457 ML-126726 HW5 ML-126207 HW7 ML-126208 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 FORM 34046 Rev. B (7-99) TABLE OF CONTENTS MODELS............................................................................................................................................... 4 GENERAL.............................................................................................................................

1 8 Standard Timer Controls 6.2 9 Recipe Timer Controls 6.2 10 Bowl Placement 6.3 10 Agitator 6.4 11 Hold to run operation 6.5 11 Power bowl lift 6.6 12 Prepare for Mixing 6.7 12 Operating Notes 6.8 13 Timer Operation 6.9 13 Recipe Mode – To enter and Exit 6.9 15 Reviewing Recipe Steps 6.9 15 Running a Recipe 6.9 16 Interrupting a Recipe 6.9 16 Entering a Special Fun 6.9 17 Enter The Access Code et…rECP] 6.9 17 Programming a Recipe [S 6.9 18 Programming a Pause or Inactive [Atth…rECP] 6.9 18 Mak

Insert the pointed end of the core probe into the product so that the tip is approximately in the middle of the product to be cooked. 2. Load the product into the oven. 3. Run the probe cable out the side of the door opening and close the door. 4. Connect the temperature probe (Fig. 6) to the connector below the control panel. 5. Press and hold the Selection Line Button next to the Timer icon. The icon will change to the Core Probe icon and display the set core probe temperature. 6. Press the Se