Remove screw at top of louvered panel on left side of unit. 2. Slide panel toward back of dispenser and lift. 3. Remove the air filter located under the louver. 4. Clean with soap and water. 5. Rinse, and replace when completely dry. Semi-annual icemaker cleaning & sanitizing Note: If icemaker and dispenser are cleaned and sanitized at the same time, icemaker should be cleaned and sanitized first. Cleaning solution Solution A: Ice machine cleaner: Prepare one gallon (3.8L) of Follett SafeCLEAN™

801 Church Lane • Easton, PA 18040, USA © Follett Corporation Toll free (800) 523-9361 • (610) 252-7301 00187153R01 Fax (610) 250-0696 • Contents Welcome to Follett.................................. 3 Before you begin............................... 3 Contact Information............................. 3 Specifications ..................................... 4 Electrical ..................................... 5 Ambient...................................... 5 Plumbing ...................................

Ambients Air Temperature1 Minimum Maximum Fahrenheit 50 F 100 F Celsius 10 C 38 C Water Temperature2 Minimum Maximum Fahrenheit 40 F 90 F Celsius 4 C 32 C 1 - Ambient air temperature is measured at the air-cooled condenser coil inlet. 2 - Ambient water temperature is measured in the icemaker float reservoir. 25CI400A/W • 25HI400A • 50CI400A/W • 50HI400A Dispenser troubleshooting Before calling for service 1. Check for ice in the ice storage area. 2. Check that congealed ice is not causing a jam.

START CAPACITOR COMPRESSORSTART RELAY (SEE NOTE #1) HI PRESSURESAFETY SWITCH P S COMPRESSOROVER-LOAD COMPRESSOR R START RUN CONDENSERFAN(AIR COOLED ONLY) WHT WHTBLK BLK #4 WHT RED GROUNDSCREW 115 60HzFROMDISPENSER BOX ICE MACHINEPOWERCONNECTION L2 DRIVE L2 FAN COMP L2 L2 L2 L1 L1 WHTBLKGRN EARTH WHTBLKBLK REDORG SWITCH COMP 2ND B-T B-E WTR 60M 20M C POWER RESET SENSOR WATER DR WATER SENSOR COMPRESSOR SWITCHI = COMP ONO = COMP OFF WATER RESERVOIR ICE MACHINE PCB VAC LINE VAC 24 BIN SIGNALCONNECTI

• Push ice transport tube onto icemaker nipple . • Install hose clamp . 5.1 Ice transport tube installation. DROP-IN • SATELLITE-FILL self-contained 11 Connect utilities to louvered docking assembly. External connections 6 . . . . . . • Remove access panel if necessary • Install drain line .. The rigid drain line from the icemaker must have at least 1/4" per foot pitch (6,4mm/0,3m). • Install icemaker potable water supply . • Replace access panel Air-cooled icemakers only • Remove access panel i

• To ensure proper ventilation (if not using supplied grille) carefully review air circulation specifications in section 4.1 • Remove and discard plastic grille . • Apply supplied gasket material around entire opening on skin to prevent air recirculation . • Attach supplied metal grille to opening in counter door (see section 4.1) . Front cover installation – undercounter 8 . . • Slide icemaker cover over machine ensuring that tabs on back of cover slip under louvers on back of louvered docking

Module No. Product OMRESSOR THERMALLY PROTECTED Easton Pennsylvania AMPS AMPS VOLTS PHASE SINGLE CHARGE LOW SIDE PART NO PSIG THE USA MADE IN OZ R C R HZ UL L NSF U HCC1000AJS, HCC1400AJS, HCC1000WJS, HCC1400WJS, HCE1000AJS, HCE1400AJS, HCE1000WJS, HCE1400WJS (See model number confi gurator on page 2 for details.) self-contained 00159939R03 801 Church Lane • Easton, PA 18040, USA Toll free (800) 523-9361 • (610) 252-7301 Fax (610) 250-0696 • Horizon Series Icemaker Model Number Configurations HC

Site preparation 2 2.1 Provide drainage, water supply and electrical power to within 6 feet (2m) of icemaker in accordance with local and national codes. Outdoor installation is not recommended and will void warranty. Electrical . • HCC1000(A/W)JS 208-230/60/1-15 amps • HCC1400(A/W)JS 208-230/60/1-20 amps • HCE1000(A/W)JS 230/50/1-15 amps‡ • HCE1400(A/W)JS 230/50/1-20 amps‡ (HCE1000A/W Requires 15 amp circuit 1.50 mm2 wire) (HCE1400A/W Requires 20 amp circuit 4.00 mm2 wire) ‡ Plug must be provid

(407mm) (458mm) 1000 series - 28.6" min. (727mm) 1400 series - 31.6" min. (303mm) 24.5" min. (623mm) No Lip . . . . . 1.75" (45mm) CROSSBRACE Undercounter installation detail – Horizon 1000 & 1400 series CAUTION • Keep ventilation openings in the appliance enclosure clear of obstruction. • To ensure proper ventilation (if not using supplied grille) carefully review air circulation specifi cations on facing page (4.1) 10 self-contained DROP-IN • SATELLITE-FILL Ice transport tube Install the ice t

Do not mount directly onto runners or channels. • There must be no lip or edge that would hinder the icemaker from sliding in or out of the louvered docking station . INTAKE AND EXHAUST GRILLE PLACEMENT: Horizon 1000 & 1400 air-cooled models only (See detail drawing on page 9) • Position the intake grille cut out in the access panel/door Note: Icemaker must be aligned with cut out and inside of access panel to provide a tight seal and prevent recirculation of hot exhaust air. • Left edge of cuto