Оценок - 6, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
Site preparation 2 2.1 Provide drainage, water supply and electrical power to within 6 feet (2m) of icemaker in accordance with local and national codes. Outdoor installation is not recommended and will void warranty. Electrical . • HCC1000(A/W)JS 208-230/60/1-15 amps • HCC1400(A/W)JS 208-230/60/1-20 amps • HCE1000(A/W)JS 230/50/1-15 amps‡ • HCE1400(A/W)JS 230/50/1-20 amps‡ (HCE1000A/W Requires 15 amp circuit 1.50 mm2 wire) (HCE1400A/W Requires 20 amp circuit 4.00 mm2 wire) ‡ Plug must be provided by end user & must conform to standard EN 60 335-2-24 of the end destination. Potable water supply . • 10-70 psi (69-483kpa) • 45 to 90 F (7 to 32 C) • Follett recommends the use of an in-line water filtration system (item# 00130286) Condenser water supply for water-cooled systems . • 10 psi min.; 150 psi max. (69kpa min.; 1034kpa max.) • 45 to 90 F (7 to 32 C) • 1.5 gallons per minute (5.68 liters per minute) Drain . • The drain line from the icemaker must have at least 1/4" per foot pitch (6,4mm/0,3m) 2.1 Installation site requirements 6 self-contained DROP-IN • SATELLITE-FILL 12" (304,8mm) min. 4" (101,6mm) . . . . . . . . . . Hot Water . Prepare the dispenser. Dispenser preparation 3 • Determine best route for ice transport tube run. Note: 12" (304,8mm) clearance is required. • Drill 1 3/4" (44,5mm) hole through either side of dispenser . • Install gasket . onto bulkhead fitting . • Attach bulkhead fitting with flat up . and tighten bulkhead nut . • Position and secure nut locking plate . with supplied screws • Verify installation of O-ring on stainless steel ice transport tube coupling . • Insert stainless steel ice transport tube coupling . into bulkhead fitting and secure with coupling cap . • Soften ice transport tube with hot water (160 F (71 C)) to ease assembly . • Attach ice transport tube to coupling with supplied hose clamp . 2.31.1 Dispenser preparation DROP-IN • SATELLITE-FILL self-contained DROP-IN • SATELLITE-FILL self-contained 8 self-contained DROP-IN • SATELLITE-FILL Install the louvered docking assembly. Louvered docking assembly 4 DOCKING STATION: Horizon 1000 & 1400 water- and air-cooled models (See detail drawing on page 9) • Position and screw louvered docking assembly to the bottom of counter inside of access panel/door 1.75" (45mm) from the front edge of the cross brace . • The mounting surface for the louvered docking assembly must be solid. Do not mount directly onto runners or channels. • There must be no lip or edge that would hinder the icemaker from sliding in or out of the louvered docking station . INTAKE AND EXHAUST GRILLE PLACEMENT: Horizon 1000 & 1400 air-cooled models only (See detail drawing on page 9) • Position the intake grille cut out in the access panel/door Note: Icemaker must be aligned with cut out and inside of access panel to provide a tight seal and prevent recirculation of hot exhaust air. • Left edge of cutout should be 1.75" (45mm) from the left side of the icemaker . • Bottom edge of cutout should ...
Эта инструкция также подходит к моделям:Прочая кухонная техника - Horizon HCC1000AJS (3.69 mb)
Прочая кухонная техника - Horizon HCE1400AJS (3.69 mb)
Прочая кухонная техника - Horizon HCC1000WJS (3.69 mb)
Прочая кухонная техника - Horizon HCC1400AJS (3.69 mb)