• The Source button on the control panel or remote control can be used to select a source. NOTE: • Always turn off the image source (computer or video) and projector before connecting or disconnecting cables. • When using a computer as the input device, set the resolution of your computer’s graphic card to 1024x768 for the optimal projected image. Refer to the Timing Charts page 30 to verify that the video signal timing of your graphics card is supported by the projector. • Many laptop computers

• Turn the projector’s display messages on and off. • Turn on power saving features. • Specify blank screen colors and startup logos. • Specify the menu language. 26 Using the menus Dot To open the menus, press the menu button on the keypad or remote. ( The menus automatically close after 60 seconds if no buttons are pressed. ) The Menu button Main menu appears. Use the arrow buttons to move up and down to highlight the desired submenu, then press the Select button. To change a menu setting, hig

Please connect the projector with your PC and turn on the projector. You can find the setup program included in the internal memory of the projector. 2. Double click on the icon to run the Setup Wizard, and then follow the on-screen instructions to continue the installation. 3. When the installation is completed, the utility icon ( ) will appear on your desktop. 4. Double click the icon to launch the converting utility. The control panel of the utility will appear as shown below: EN To convert P

16.4’ (5 m) 60° 16.4’ (5 m) Used to adjust zoom. (P20) ON-OFF FOCUS D.ZOOM ZOOM MENU SCREEN MUTE 11 2 2 3 3 4 Z F Z F D D KEYSTONE KEYS FREEZE AUTO PC ADJ. AUTO COLOR.M NO SHOW IMAGE INPUT INPUT LENS SHIFT LENS VOLUME VOLUME SELECT ZOOM BUTTON Used to adjust focus. (P20)NO SHOW BUTTON Used to turn picture into black image. (P21) Used to select DIGITAL ZOOM +/– mode and resize image. (P30) KEYSTONE BUTTON Used to correct keystone distortion. (P20, 37) Used to select image level. (P27, 33) 60° WIR

This projector provides many convenient features and functions. Operating the projector properly enables you to manage those features and maintains it in better condition for a considerable time. Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents. If your projector seems to operate improperly, read this manual again, check operations and cable connections and try the solutions in the “TROUBLESHOOTING” section at the end o

Manual Sync The projector adjusts signal synchronization automatically for most computers. But if the projected computer image looks fuzzy or streaked, try turning Auto Image off then back on again. If the image still looks bad, try adjusting the signal synchronization manually: 1 Turn Auto Image off. 2 Highlight Manual sync, then press either mouse button repeatedly until the image is sharp and free of streaks. Manual Tracking The projector adjusts tracking automatically to match the video sign

If that doesn’t clear up the image, turn Auto Image off and adjust the sync (page 28) and/or the tracking (page 29) manually. 5 If the colors don’t look right, adjust the brightness (page 25). Using the Remote Control Point the remote control at the projection screen or at the front or rear of the projector. The range for optimum operation is about 40 feet. If you point the remote at the projection screen, the distance to the screen and back to the projector must be less than or equal to 40 feet

All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of BOXLIGHT Corporation. Disclaimer BOXLIGHT Corporation makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disc

correctly. Make sure the USB port is USB 2.0... Try a different USB 2.0 port or another computer... Check the power led indicator is.. ON. Try connecting to USB port of the Notebook directly instead .. of through the hub. Unplug all other USB devices from the system... Make sure to restart your computer after thedriver .. installation. Unplug the device and re-insert it... The projected image is too dark Use the projector in a darker environment... Increase the brightness by using the AC power a

4 If you want the projector display to be the same as the PowerBook’s screen display, turn on video mirroring (called SimulScan in newer PowerBooks). See “Using Video Mirroring with a PowerBook Computer” on page 46 for additional information. audio cable CablePro Lite cable PowerBook video-out cable Mac adaptor or monitor adaptor FIGURE 6 Connecting the CablePro Lite computer cable to a Macintosh Do you want to play your computer’s audio on the projector? NOTE: If you want to control your 1 Plug