Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
4 If you want the projector display to be the same as the PowerBook’s screen display, turn on video mirroring (called SimulScan in newer PowerBooks). See “Using Video Mirroring with a PowerBook Computer” on page 46 for additional information. audio cable CablePro Lite cable PowerBook video-out cable Mac adaptor or monitor adaptor FIGURE 6 Connecting the CablePro Lite computer cable to a Macintosh Do you want to play your computer’s audio on the projector? NOTE: If you want to control your 1 Plug either end of the audio cable into the audio connector on computer’s mouse from the your computer. projector, purchase the optional 2 Plug the other end of the audio cable into the connector CablePro and remote. on the projector. Connecting a Video Player 1 If your video player uses a round, one-prong composite video connector, you’ll need only the A/V cable that shipped with the projector. • If your video player uses a round, four-prong S-video connector, you’ll need an S-video cable in addition to the A/V cable. The S-video cable is sold separately. (See “Optional Accessories” on page 40.) 2 Plug the A/V cable’s yellow connector into the “video-out” port on your video player (Figure 7). This port may be labeled “To Monitor.” • If you’re using an S-video cable, connect it to the “s-video out” connector on the video player (Figure 8). 3 Plug the other yellow connector into the composite connector on the back of the projector. • If you’re using S-video, plug the other end of the cable into the “s-video” connector on the projector (Figure 8). audio/video cable FIGURE 7 Connecting the projector to a video player using the standard A/V cable (with composite video connector) Setting up the Projector S-video cable CAUTION: Your video player may also have a “Video Out” port for a coaxial cable connection. DO NOT use this to connect to the projector. A/V cable FIGURE 8 Connecting the projector to a video player using an S-video cable and the audio connectors on the standard A/V cable 4 Plug the A/V cable’s white connector into the left “audio out” port on your video player. Plug the cable’s red connector into the right “audio out” port on the video player (Figure 7 and Figure 8). • If you’re using an S-video cable, the yellow connectors on the A/V cable remain unused (Figure 8). 5 Plug the A/V cable’s other white and red connectors to the left and right “audio in” ports on the projector. The projector is compatible with these major broadcast video standards: NTSC, NTSC 4.43, PAL, PAL-M, PAL-N, and SECAM. It automatically adjusts to optimize its performance for the incoming video. The input signals for SECAM, PAL-M, and PAL-N video are similar to other video signals and cannot be automatically detected, therefore they must be chosen manually. See “Video Standard” on page 23 for details. Powering up the Projector and Adjusting the Image 1 Remove the lens cap. 2 Plug the power cord into the side of the projector, then plug it into your electrical outlet. A surge-protected power strip is recommended. 3 Turn on the projector by pressing the “I” side of the power switch (see Figure 2 on page 3). • The startup screen displays and the Power LED on top of the projector lights up (Figure 11 on page 15). 4 If you connected a video player, turn it on. • The video image should display on the projection screen. If a computer source is active, press the source button on the keypad (page 15) to display your video image. You can select a default source to determine which source the projector examines first during power-up for active video; see “Default Source” on page 24. • Use the volume buttons to adjust the volume. 5 Turn on your computer. • The computer image should display on the projection screen. (If a video source is active, press the source button to display your computer’s image.) • If necessary, make adjustments to the image from the projector’s on-screen menus. To open the menus, press the menu button on the keypad, then select the Display or Image sub-menu. For more information about the menus, see page 17. NOTE: Always use the power cord that shipped with the projector. NOTE: With some computers, the order in which you power up the equipment is very important. Most computers should be turned on last, after all other peripherals have been turned on. Refer to your computer’s documentation to determine the correct order. Setting up the Projector CAUTION: When you disconnect the projector after you have switched it off, always remove the power cord from the electrical outlet first, then remove it from the projector. Turning Off the Projector If you want to turn off the projector for a short period of time, press the standby button on the keypad. This blanks the screen for fifteen minutes, but keeps the projector running. (You can change the amount of time the projector stays in standby mode; see “Standby Time” on page 23 for details.) After 15 minutes, the lamp goes out (the projector keeps running). To exit standby mode, press th...