Войти:

Attwood 5330

Скачали: 8Размер: 503 kb    Производитель: Attwood  
Категория: Лодочное оборудование

NOTE: Do not use light pole as a flagpole or handle. MAINTENANCE When not in use, store in Pole Light Storage Clips (Attwood 7571). Choose a storage location where light will not be damaged or be in constant contact with water. Replacing Bulb 1. Unscrew lens counter-clockwise and remove. Pull bulb straight up (Figure 4) 2. Replace bulb with #906 9-Watt Wedge Base Replacement Bulb (Attwood 9235-7) available in marine, auto, and convenience stores. 3. Screw lens clockwise onto pole. 4. If lens req

Attwood 5320

Скачали: 5Размер: 503 kb    Производитель: Attwood  
Категория: Лодочное оборудование

NOTE: Periodically check pole to make sure it is secure. loosens, then pull up on pole. (Figure 3) Figure 3 Locking Collar • Lower Ring • #91020, #91024, Screw • or #91026 #91022 TO CONVERT POLE FOR USE WITHOUT LOCKING COLLAR 1. For bases that do not accept locking collar, remove screw at bottom of pole. Slide locking collar off end of pole. 2. Replace screw in the upper screw hole. TO ADJUST ANTI-GLARE ARTICULATING HEAD (5330 Series) For best glare reduction, adjust the light while the boat is

Attwood 5310

Скачали: 6Размер: 503 kb    Производитель: Attwood  
Категория: Лодочное оборудование

A 03-02 This product carries the standard Attwood one-year warranty. See or Product Catalog for details. Lights meet USCG CFR 183.810, ABYC A-16 requirements, and all applicable standards as tested by Imanna Labs, 7/19/2002. 2 Nautical Mile visibility. Use Lamp 9235, #906 13V, 6 Candle Power. CAUTION: Read all instructions carefully before installing and using this product. All positive (+12V DC) lighting wires require a 1-amp fuse to protect circuits and vessel. The aluminum light pole is not g

Attwood 5300

Скачали: 3Размер: 503 kb    Производитель: Attwood  
Категория: Лодочное оборудование

Mount the anti-glare light in a position so that: • Light output is flat and parallel to water when boat is floating. • Light shines 360°, unobstructed. • Light does not shine on operator, or reflect off any part of the boat in the operator’s field of vision. Figure 1 7.5° or 39-3/8" One meter INSTALLATION Figure 2 Base #911339, 911370, or 911445 Pole Screw • Poles Without Locking Collar (5300 Series) 1. Align pole screw with slot in the existing base. Insert pole into base (Figure 2). 2. Press

Attwood 5100

Скачали: 8Размер: 494 kb    Производитель: Attwood  
Категория: Лодочное оборудование

Attwood 5110

Скачали: 8Размер: 494 kb    Производитель: Attwood  
Категория: Лодочное оборудование

Attwood 5980

Скачали: 11Размер: 480 kb    Производитель: Attwood  
Категория: Лодочное оборудование

• Non-silicone sealant. WARNING: To prevent personal injury, disconnect the power source when installing or servicing this product. Always remove the boat from the water before using 120V AC power tools. LOCATION (All-Round Lights) All-Round Lights must be mounted a minimum of 1 meter above the sidelights, on a smooth surface where the 360° beam will not be obstructed. Light must not shine on operator or on anything in operator’s field of view. (Figure 1) Important: Before drilling mounting hole

Attwood 5940

Скачали: 8Размер: 480 kb    Производитель: Attwood  
Категория: Лодочное оборудование

2. Place sidelight(s) in position as shown in Figure 2. Important: Before drilling, be sure that sidelights will shine straight ahead and within 5° of horizontal when boat is floating. 3. For Bi-Color Combination light, mark and drill a 3/4" (19mm) diameter hole on the boat centerline. For Sidelight Pairs, mark and drill a 3/4" (19mm) diameter hole on each side deck of the boat, equal distance from the bow. (Figure 3) 4. Thread wire leads and base stem into hole. Align centerline mark with strai

Attwood 5080

Скачали: 10Размер: 480 kb    Производитель: Attwood  
Категория: Лодочное оборудование

For Sidelight Pairs, mark and drill a 3/4" (19mm) diameter hole on each side deck of the boat, equal distance from the bow. (Figure 3) 4. Thread wire leads and base stem into hole. Align centerline mark with straight-ahead position and mark location of screw holes. 5. Remove base and drill 1/8" (3mm) pilot holes for both screws. 6. Bring 12V DC (+) and (-) wires up through deck hole. Connect wires using waterproof crimp on butt joint connectors. 7. Activate light to verify proper operation. 8. A

Attwood 5040

Скачали: 8Размер: 480 kb    Производитель: Attwood  
Категория: Лодочное оборудование

The lens completely encloses the bulb and socket for a splash resistant seal. Lights meet USCG CFR 183.810, ABYC A-16 requirements, and all applicable standards as tested by Imanna Labs, March 1997. 5040, 5045, and 5080 are Sidelights with 1 Nautical Mile visibility. 5940 and 5980 are All-Round Lights with 2 Nautical Mile visibility. All use Lamp 9235, #906, 13V, 6 Candle Power. REQUIRED FOR INSTALLATION • Cordless drill with 1/8", 3/8", and 3/4" (3, 10, and 19mm) bits. • Screwdriver. • Two #8 o





Категории