Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
NOTE: Periodically check pole to make sure it is secure. loosens, then pull up on pole. (Figure 3) Figure 3 Locking Collar • Lower Ring • #91020, #91024, Screw • or #91026 #91022 TO CONVERT POLE FOR USE WITHOUT LOCKING COLLAR 1. For bases that do not accept locking collar, remove screw at bottom of pole. Slide locking collar off end of pole. 2. Replace screw in the upper screw hole. TO ADJUST ANTI-GLARE ARTICULATING HEAD (5330 Series) For best glare reduction, adjust the light while the boat is floating, or at the same attitude as if it were floating. 1. Unscrew lens counter-clockwise and remove. Remove bulb (Figure 4) 2. Remove the pivot screw. Pull the top pivot up and away from yoke. Place a small level on top of the socket and rotate to level position. 3. When it is level, push yoke and pivot back together. Replace and tighten screw. (Do not over tighten.) Replace bulb. Figure 4 Lens Off On Bulb #906 Pivot Screw OPERATION After installation, check lights to verify proper operation. Regulations require lights to be operated with a three-position switch for: • Running lights (sidelights and all-round light); Anchor lights (all-round light only); Off. NOTE: Do not use light pole as a flagpole or handle. MAINTENANCE When not in use, store in Pole Light Storage Clips (Attwood 7571). Choose a storage location where light will not be damaged or be in constant contact with water. Replacing Bulb 1. Unscrew lens counter-clockwise and remove. Pull bulb straight up (Figure 4) 2. Replace bulb with #906 9-Watt Wedge Base Replacement Bulb (Attwood 9235-7) available in marine, auto, and convenience stores. 3. Screw lens clockwise onto pole. 4. If lens requires replacement, order Attwood #912852. Clean the light with a mild soap and warm water solution. Never use solvents or abrasives that may damage the lens or light housing. © 2003 Attwood Corporation 1016 N. Monroe Street, Lowell, MI 49331-0260 3. Faites glisser le collier jusqu’a la base ; tournez jusqu’a ce que vous 3® Feu d’horizon antireflet Serie 5300, 5310 ou 5320: Tete fixe Serie 5330: Tete articulee Instructions d’installation CONSERVEZ CES INSTRUCTIONS Numero de formule 69388 Rev. A 03-02 Ce produit est protege par une garantie Attwood standard d’un an. Pour de plus amples renseignements, consultez ou le catalogue de produits. Les lampes repondent aux exigences USCG CFR 183.810, ABYC A-16 et a tous les standards applicables selon les tests des Laboratoires Imanna, 19/7/2002. Visibilite de 2 milles nautiques. Utiliser la lampe 9235, #906 13 volts, eclairage equivalent a 6 chandelles. ATTENTION: Lisez attentivement toutes les instructions avant d’installer ou d’utiliser ce produit. Tous les fils d’eclairage positifs (+12 V CC) necessitent un fusible de 1 A pour assurer la protection du circuit et le bateau. Le mat de feu en aluminium n’est pas mis a la masse. ASSUREZ-VOUS QUE LA SOURCE D’ALIMENTATION EST DE 12 V CC SEULEMENT. DES TENSIONS PLUS ELEVEES POUR...
Эта инструкция также подходит к моделям:Лодочное оборудование - 5310 (503.45 kb)
Лодочное оборудование - 5300 (503.45 kb)
Лодочное оборудование - 5330 (503.45 kb)