OPERATION .saûiiflusd 4.3 MANUALLY COPYING THE MAIN PATH TO ZONE2, ZONE3, OR RECORD When Main is copied to another Path, the Source selected in MAIN is directed to ZONE2, ZONE3, or RECORD from either analog or digital inputs. If a source component's audio is connected to the AVM 50 using digital connection only, then the Copy function is the only way to deliver the sound to another Path. Front Panel Press MAIN simultaneously with ZONE2, ZONE3, or REC. Use MAIN to select the Source. Remote

0.006% (AES17 Filter) Digital Inputs at 24/48 ............................................ 0.004% (AES17 Filter) IMD (CCIF at 15 kHz & 16 kHz) Analog-Direct Inputs..........................................................0.001% Analog-DSP Inputs at 24/48....................................................0.003% Digital Inputs at 24/48 .........................................................0.001% S/N Ratio (ref. 2.0 Vrms, IEC-A Filter) Analog-Direct Inputs................................

NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowpoint within an equilateral triangle ^ warns of the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle warns users /|\ of the presence of important operating and maintenance < > (servicing) instructions in the literature

With some control systems, an emitter face-to-face with an IR receiver may be needed. 2.6 I.R. (INFRA RED) EMITTERS External IR emitters allow control of your source components from any location in your home that has an IR receiver wired to the back of the AVM 50. After positioning the IR emitter according to its instructions, connect it to I.R. EMITTER output. Commands that come in through the rear I.R. RECEIVER connections are re-transmitted through the IR emitters. 2.7 POWER To connect po

Be sure that the source and the power amplifier are turned on or will be on at the Timer turn-on time. If your components have trigger inputs, you can set a processor trigger to turn them on (see section 3.11). On-Volume: Sets the volume that will play when a Timer turns the power on. The volume increases slowly when a Timer turns the power on. 22 3. SETUP continued Example 1: Select a source for the ZONE2 Timer: • Enter the setup menu. Go to SET TIME/TIMERS and press SELECT. • Press the

Be sure to read this manual carefully and follow these instructions in order to keep your unit performing and sounding its best. Please contact Sonic Frontiers if you have any questions, a Customer Service Representative will be pleased to assist you. WHAT’S IN THE BOX? In addition to the Amp 1, it’s cover, and the operating manual you are presently reading (with associated inserts and warranty card), there are a few more items to take inventory of before steps are taken to make the Anthem Amp 1

12. Outdoor Antenna Grounding – If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to the proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna-discharge unit, size of grounding conductors, location of antenna-disc

Note: The amplifier is equipped with a thermal shut off feature. If it overheats, the affected channel will remain off until the temperature falls below the shut off threshold. There are no fuses inside the amplifier. If an overcurrent condition occurs in any channel, an AC line breaker located on the rear panel will trip. To reset, push it back in. 2. CONNECTIONS AND OPERATION continued… A A5 CAUTION 2.4 REAR PANEL LAYOUT 1 – Circuit breaker (two in Statement A5) 2 – Single Ended RCA Input 3 –

In the operate mode, the outputs are connected and the SFP-1 operates normally. B-Power Indicator LED - This LED lights when the SFP-1 is on and receiving power from the AC source. It will flash at one second intervals during warmup delay and muting. C-Power Switch - This toggle switch, when in the ON position, allows the SFP-1 to receive power, rendering the SFP-1 operational as indicated by the Power Indicator LED (B). When the switch is in the OFF position the SFP-1 is not receiving power and

. . . . . . . . . . . . . . . . . . . . 180 W, 265 W, 340 W* *Special Test Conditions Required for 2 . Frequency Response . . . . . . . . . . . . . . . . . . . . . . . 20 Hz to 20 kHz (+0, -0.15 dB), 5 Hz to 100 kHz (+0, -2 dB) THD+N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.0015% at 1 kHz, 0.03% at 20 kHz (100 W into 8 .) Power Bandwidth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Hz to 80 kHz (+0, -3 dB, 200 W into 8 .) S