Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
With some control systems, an emitter face-to-face with an IR receiver may be needed. 2.6 I.R. (INFRA RED) EMITTERS External IR emitters allow control of your source components from any location in your home that has an IR receiver wired to the back of the AVM 50. After positioning the IR emitter according to its instructions, connect it to I.R. EMITTER output. Commands that come in through the rear I.R. RECEIVER connections are re-transmitted through the IR emitters. 2.7 POWER To connect power, use the supplied double-insulated power cord and then turn on the Rear Panel AC switch. 11 2. CONNECTIONS istiiausd Example 1: DVD PIayer to AVM 50 to Main Display HDTV receivers are connected the same way as DVD players. IO: HDMI IN ■ - DVD D. Connect if using ZONE2/3 or REC A A Connect if using digital REC-OUT or if source's video output is DVI AA Connect if using ZONE2 A O Connect for MAIN ®L ® R AUDIO OUT ® COAX OUT ® ® ® YPbPr OUT HDMI OUT \ 2. CONNECTIONS iûûiiausd Example 2: Video Recorder to AVM 50 H goooooo <90 ooooo ®®®® ® ® ® ® ® ® ® ® 0® © ®-0 0 AN, iLOQ AUDI! f - OUT For ZONE2, ZONE3, and REC, in most cases you must use the same input type as the output type. If MAIN uses a different input connection, all you need to do is add these connections for ZONE2, ZONE3, and REC. A A JÜ 2. CONNECTIONS Example 3: AVM 50 to Amplifiers and Subwoofer (Balanced connection shown, single-ended is similar) »~®®® c©@© ®®®® ® ® ® ® ® ® ®®®® © ©■© © ANALOG AUDIO - OUT Trigger Setup Suggestion: If it is not necessary to have both amplifiers turned on when stereo sources are playing, set triggers to turn on only the 2-channel amplifier when a stereo source is selected (see section 3.9). A I § I A II MCA 50 14 3. SETUP MENU For optimum performance and enjoyment, your AVM 50 should be properly set up. This may appear like a lot of work, however, most settings do not need to be changed from the factory defaults. The most important things are entering information about your display (menu 1) and speakers (menu 3) if the defaults do not apply, the distance from each speaker to the listening area (menu 4), balancing output levels to one another (menu 5), and input connections (menu 6). The rest is preference - the surround mode presets in menu 7, for example, should be set up after you have played a variety of source material and have decided which surround modes you like best. For proper audio balance, menus that involve test signals must be set up in the order that they appear. Illustrations throughout this section show the On-Screen display menus in that order. For ease of viewing, use of the On-Screen display is recommended, although the Front Panel display shows similar information. Alternatively, mi ost of the setura can be done on your personal computer through RS-232 connection and a program from our web site, called Setup Editor. This can also save your configuration as a backup file. Setup Editor cannot playtest signals - calibration still has to be done through the Setup Menu. HOW TO ENlDR THTV SEW ME0U The Setup Menu can be accessed from either MAIN or ZONE2. The On-Screen display shows only in that Path (MAIN - any output except Composite, ZONE2 - S-Video only). Test signals only play from MAIN. To enter the Sra:up Megu: Remote Control Make sure the appropriate control mode is set, then press SUB/Ltf E (SETUP) for 3k econds. Front Panel Make sure the appropriate Path is selected, then press and hold STATUS (Setup) for 3 seconds. ZONE 2 ZONE 3 PATH HOW TO NAVIGATE IN THlE SETUP MENU • Use the ^ ▼ bmwons|ra scroll through menus. • Press SELECT to choose a menu item. • Use the ^ ▼ and i ► buttons to change settings. • Press BACK to return to previous item or menu. HOW TO EXIT FROM THE SETUP MENU Press BACK as many times as necessary. Each time BACK is pressed, the previous item or menu returns. The Setup will exit by itself if not used or 5 minutes to prevent the potential of a burned-in On-Screen image. 3. SETUP MENU .iûflliûUSÜ SETTING UP THE AVM 50 When you enter the Setup Menu, your On-Screen display will show the menu below. Only 8 menu items can be displayed at one time. To go to a submenu, highlight a menu item in red and then press SELECT. If current settings do not work with your display, use the Front Panel display to view the Setup until making the appropriate selections. ANTHEM AVM 50 SETUP 1. VIDEO OUTPUT 2. SET TIME / TIMERS 3. SPEAKER CONFIG 4. LISTENER POSITION S. LEVEL CALIBRATION б. SOURCE SETUP 7. SOURCE PRESETS 8. ANALOG INPUT LEVELS 9. ADC / AUDIO OUTPUT 10. VOLUMES / PATH NAMES 11. TRIGGER / IR / RS232 12. DISPLAYS / TIMEOUT 13. SAVE / LOAD SETTINGS 14. LOCKOUT / PASSWORDS SELECT Enters Submenu 3.1 VIDEO OUTPUT Highlighting '1. VIDEO OUTPUT' and then pressing SELECT displays this menu: 1. VIDEO OUTPUT a. VIDEO OUT CONFIG 1 b. VIDEO OUT CONFIG 2 c. VIDEO OUT CONFIG 3 d. VIDEO OUT CONFIG 4 V...