. Introduction . Installation of Ethernet Driver -for Windows 95 -for Windows 98 -for Windows NT . Further Information CHAPTER 4.1 Introduction The IPPC-9120/9150 is equipped with a high performance 32-bit Ethernet chipset which is fully compliant with IEEE 802.3 100 Mbps CSMA/CD standards. It is supported by major network operating systems. It is also both 100Base-T and 10Base-T compatible. The medium type can be configured via the RSET8139.exe program included on the utility disk. The Ethernet

The options are: 3 (Default), 1. Serial Port 1/2/3/4 IRQ The IRQ of serial port 1/2/3/4 can share the same one or not. The options are: 4/3/10/5(default), 4/3/3/3, 4/3/10/10, 4/3/4/3, share 3, share 3, share 4, share 5, share 10 (share IRQ is reserved). Vector Hi/Low select (Reserved) You can select the interrupt vector level. The options are: low (default), high Vector Address Decoder (Reserved) You can choose the interrupt vector address, the default is 200. 9.11 Password Setting To enable the

All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable. However, the original manufacturer assumes no responsibility for its use, nor for any infrin

You may open the CD-ROM drive door by pushing the eject button located on the door of the drive. When the door opens, you can pull the tray out completely and clip in the CD onto the tray face up; then push the door in completely. The light on the CD door will light up while the CD-RPOM is being accessed. 2.3.8 Slim FDD Drive A floppy disk drive is essential as the floppy disk is still an important medium for transferring data between systems. Floppy disks are available in all computer stores an

10. All cautions and warnings on the equipment should be noted. 11. If the equipment is not used for a long time, disconnect it from the power source to avoid damage by transient over-voltage. 12. Never open the equipment. For safety reasons, the equipment should be opened only by qualified service personnel. 13. If any of the following situations arises, get the equipment checked by service personnel: a. The power cord or plug is damaged. b. Liquid has penetrated into the equipment. c. The equi

5-58 ADAM 4000 Series User’s Manual 4011, 4011D, 4012 Chapter 5 @AARE Name Read Event Counter command Description The addressed module is instructed to return its event counter value. Syntax @AARE(cr) @ is a delimiter character. AA (range 00-FF) represents the 2-character hexadecimal address of an analog input module. RE is the Reads Event Counter command. (cr) represents terminating character, carriage return (0Dh). Response !AA(data)(cr) if the command was valid. There is no response if the mo

You can create a maximum of eight arrays from the BIOS. See “Understanding Arrays” if you have not yet decided what type of arrays you need. DNS-3200 User’s Manual 54 Notes: 1. In some circumstances, more than eight arrays are possible and may appear to function properly, but are not supported by Broadcom. 2. For redundant arrays, the creation process does not complete until after the operating system and controller drivers have been installed and you have booted into the operating system contex

68 Optional Extras for the PCM-9587 ... 69 PCM-10586-6200E Cable kit for PCM-9587........................................... 70 Table D.1: PCM-10586-6200E wiring kit 9587........................... 70 Mechanical Drawings ....................... 71 Mechanical Drawings.............................................................................. 72 Figure E.1 PCM-9587 Mechanical Drawing (component side) .. 72 Figure E.2 PCM-9587 Mechanical Drawing (solder side) .......... 73 PCM-9587 User Manual v

50 A.2.4 IOCTL_WDT_GETTIMEOUT: .................................. 51 A.2.5 IOCTL_WDT_SETTIMEOUT: .................................. 51 A.2.6 IOCTL_WDT_REBOOT: ........................................... 51 A.3 Examples ......................................................................... 52 Appendix B Fuse Specifications ........................................ 56 B.1 Fuse Specifications.......................................................... 56 B.2 Fuse Replacement .......................

1. Device Server List Area: All devices will be searched and listed in this area. You can arrange different favorite group and virtual COM ports. 2. Device Server Information Area: Click on the serial device server or move cursor to the serial device server, the related information will be shown on this area. 3. Configuration Area: Click on the item on the Device Server List Area, the configuration page will display on the area. 4. Quick Tool Area: Useful management functions shortcut. EKI-1351/