2 Years 90 Days 90 Days 100 Series Trimmers, Stick Edgers, Hedge Trimmers Lifetime Ignition Warranty (Parts Only). Lifetime Shaft Warranty. 2 Years 1 Year 90 Days 200 & 300 Series Trimmers, Brushcutters, Clearing Saws, Stick Edgers, Hovering Trimmers & Hedge Trimmers Lifetime Ignition Warranty (Parts Only) and Lifetime Shaft Warranty apply to these products (excludes Hovering Trimmers). 2 Years 1 Year 90 Days Blowers (Lifetime Ignition Warranty - Parts Only) 2 Years 2 Years 90 Days Pole Pruners,

Beatrice, NE. Printed in U.S.A. CONTENTS SAfETy..................................................................... 5 GENERAL OPERATION................................ 5 SLOPE OPERATION.....................................5 CHILDREN ................................................... 6 SERVICE....................................................... 6 CONTAINER CONTENTS ......................................... 8 ASSEmBLy ............................................................... 9 OPERATION

101 89 75-26 Symbols WARNING! The edger can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. Read through the Operator's Manual carefully and understand the content before using the machine. Always use: • A protective helmet where there is a risk of falling objects. • Ear protection • Approved eye protection • Max. speed of output axle, rpm • This product is in accordance with applicable CE directives. • Beware of thrown objects and ricoche

Make sure the throttle control is locked at the idle setting when the throttle lock is released. Press the throttle lock and make sure it returns to its original position when you release it. Check that the throttle control and throttle lock move freely and that the return springs work properly. See instructions under the heading Start. Start the machine and apply full throttle. Release the throttle and check that the sweeper rollers stops and remains at a standstill. If the sweeper rollers rota

Use HUSQVARNA special grease. The grease in the bevel gear does not normally need to be changed except if repairs are carried out. Air filter The air filter must be regularly cleaned to remove dust and dirt in order to avoid: • Carburettor malfunctions • Starting problems • Loss of engine power • Unnecessary wear to engine parts • Excessive fuel consumption. Clean the filter every 25 hours, or more regularly if conditions are exceptionally dusty. ! WARNING! Mufflers fitted with catalytic convert

539 111139....1 .... COVER ASSM, COMPLETE 11.. 532 179746....1 .... BAGGER, FRAME INCLUDES ITEMS 2-4 12.. 532 192786....1 .... PIN, HINGE 2.. 532 127533....1 .... SCREEN, COVER 13.. 532 400226....2 .... CONTAINER, SOFT BAG 3.. 532 155042....1 .... STRIP, REINFORCEMENT 14.. 539 105408....8 .... WASHER #10 FLAT 4.. 532 130895....1 .... LATCH HANDLE, COVER 15.. 539 976977....4 .... NUT #10-24 HEX NYLOC 5.. 539 976952....9 .... SCREW #10-24 x 5/8 16.. 539 106312....4 .... HMS #10-24 x . 6.. 532 1327

Remove components from carton and place spreader upside down on a padded surface. Install LH. & RH. handle braces to frame as shown using four (4) 1/4-20 x 2 1/4” hex bolts and nuts but do not tighten. ASSEMBLYASSEMBLYASSEMBLYASSEMBLY3. Turn spreader upright. For ease of assembly, make sure ON/OFF cable is on top of handle braces. With DOT on the handle assembly facing as shown, secure clamp bracket using a #10 x 3/4 slotted sheet metal screw. Install end of handle assembly between handle braces

1. Place hitch on the rear of the mower. Rear Engine Guard Engine Guard Bolts Engine Guard Bolts 3. Install two of the previously removed bolts through rear of the hitch weldment. 4. Secure the sides of the hitch to the frame with 5/16-18 x . bolts and washers from the new hardware, (two per each side). Previously Removed Hardware Hitch Mount Tube 8063-044 8063-045 8063-046 BAGGER SUPPORT -2008 and Prior Models 10 ASSEMBLY 1. Position upper chute support against bagger inlet, flush at outer edge

-Never store the machine or fuel container inside where there is an open flame, such as a water heater. • Never run a machine inside a closed area. • Keep nuts and bolts, especially blade attachment bolts, tight and keep equipment in good condition. • Never tamper with safety devices. Check there proper operation regularly. CAUTION CAUTION CAUTION SAFETY RULES SAFE OPERATION PRACTICES FOR RIDE-ON MOWERS • Keep machine free of grass, leaves, or other debris buildup. Clean oil or fuel spillage. Al