Diese Garantieleistung bezieht sich auf alle wesentlichen Mangel des Gerates, die nachweislich auf Materialoder Fabrikationsfehler zuruckzufuhren sind. Sie erfolgt durch die Ersatzlieferung eines einwandfreien Gerates oder durch die kostenlose Reparatur des eingesandten Gerates nach unserer Wahl, wenn folgende Voraussetzungen gewahrleistet sind: . Das Gerat wurde sachgema. und laut den Empfehlungen in der Gebrauchsanweisung behandelt. . Es wurde weder vom Kaufer noch von einem Dritten ver sucht,

8. Fit the cassette cover I on the filament cassette holder M so that you hear both locking clips J click into place. When replacing the cover, ensure that the filament is inside the metal case and is not trapped. v If the cassette cover I cannot be touched down, turn the filament cassette E to and fro, until the filament cassette E is completely in the filament cassette holder M. E 7 H G F L E GB Recommended storage: We recommend that you hang your Turbotrimmer from the cable lock. Hanging stor

2. Remove Filler Cap. Remove Filler cap only when ready to fill hydraulic Tank with Oil. Do Not leave the Cap off and the system Open, always keep system closed when possible. Avoid any oil contamination. (See Figure 29) 3. Avoid Hydraulic Contamination by filtering the Hydraulic Oil while filling the Hydraulic Tank. Filter bug- gies or carts are commercially available for Hydraulic system cleanup and Oil transfer. These consist of high capacity filter, a Circulating Pump, a Drive Motor and hose

Alamo Group is not responsible for modifications to the MountKit to accommodate these differences. ALAMO INDUSTRIAL 1502 E. Walnut Seguin, Texas 78155 210-379-1480 © 2005 Alamo Group Inc. TO THE OWNER/OPERATOR/DEALER All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment

Make certain that the hole cut is far enough over that it will not interfere with operators foot room. Cut hole through floor mat and floor using a round 2" hole saw (See Figure 12). After you cut the rubber mat with the hole saw pull the piece of rubber out of saw, this will make it easier to cut through the floor. (See Figure 12) 3. Install Cable / Wire Harness Boot Cover. The Boot cover will be modified, using a knife cut an "X" shaped cut across the small hole at the top. This cut will be cu

The exhaust fumes can be hazardous to your health. (SG-23) Start tractor only when properly seated in the Tractor seat. Starting a tractor in gear can result in injury or death. Read the Tractor operators manual for proper starting instructions. (SG-13) 6. CONNECTING THE MOWER TO THE TRACTOR Use extreme caution when connecting the mower to the tractor. The mower should be securely resting at ground level or setting on blocks. Keep hands and feet from under the mower deck and clear of pinch point

READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. C01Cover ALAMO INDUSTRIAL® 1502 E. Walnut Seguin, Texas 78155 830-372-3551 Email: parts@alamo-industrial.com ©2009 Alamo Group Inc. $0.00 To the Owner/Operator/Dealer All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufac

Parts Section -6 AXLE HYD SCHEMATIC - LEVEL LIFT OPTION Hydro 10 and 15 ft (08-05) Rev 01-08 ©2008 Alamo Group Inc. Parts Section -7 AXLE HYD SCHEMATIC - LEVEL LIFT OPTION Continued... ITEM PART NO. QTY. DESCRIPTION 1 8719B 1 CYL. ASY, 3-1/2" BORE (CNTR AXLE) 2 8720B 1 CYL. ASY, 3-1/4" BORE (RH WG AXLE) 3 7521B 1 CYL. ASY, 3" BORE (LH WG AXLE) 4 02965360 1 HOSE ASY, #6 - 6FJX - 6FJX - 202" LG 5 02981345 1 HOSE ASY, #6 - 6FJX - 6 FJX - 192" LG 02979578 1 HOSE ASY, #6 - 6FJX - 6FJX - 166" LG 6 029

(SG-21) 9.1 Tractor Pre-Operation Inspection/Service Refer to the tractor operator’s manual to ensure a complete pre-operation inspection and scheduled service is performed according to the manufacturers recommendations. The following are some of the items that require daily service and inspection: • Tire condition/air pressure • Wheel lug bolts • Steering linkage • PTO shield • SMV sign is clean and visible • Tractor’s lights are clean and functional • Tractor Seat belt is in good condition • T

2. Place lifting device (scissors jack, hydraulic jack) under center of cutter housing. 3. Remove hex nuts, washers and carriage bolts from bracket at each end of roller. Make certain that roller bracket is free to move once the fasteners are removed. A stuck roller could drop suddenly and cause and injury. 4. Use lifting device to reposition cutter housing to desired cutting height. Align bracket holes with cutterhousing holes, then reinstall fasteners. Refer to cutting height decal on mower or