Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
Remove components from carton and place spreader upside down on a padded surface. Install LH. & RH. handle braces to frame as shown using four (4) 1/4-20 x 2 1/4” hex bolts and nuts but do not tighten. ASSEMBLYASSEMBLYASSEMBLYASSEMBLY3. Turn spreader upright. For ease of assembly, make sure ON/OFF cable is on top of handle braces. With DOT on the handle assembly facing as shown, secure clamp bracket using a #10 x 3/4 slotted sheet metal screw. Install end of handle assembly between handle braces and secure with (2) 1/4-20 x 1 1/2” hex bolts and nuts. 2. Slide wheels onto end of axle with the hub facing toward frame. Wheels are identical to ease assembly. Align the hole in the wheel hub and the hole in the axle as shown. Secure drive wheel to axle with 3/16 dia. x 2” cotter pin. Insert 1/8 dia. x 1 1/4” cotter pin in the hole near the end of axle to retain free turning wheel. DOT RH. Handle Brace LH. Handle Brace 1/4-20 x 2 1/4” Hex Bolt 1/4-20 Hex Nut Drive Wheel Free Turning Wheel 3/16 Dia x 2” Cotter Pin 1/8 Dia x 1 1/4” Cotter Pin 2 1/4-20 Hex Nut 1/4-20 x 1 1/2” Hex Bolt Handle Assembly ON/OFF Cable Clamp Bracket #10 x 3/4 Sheet Metal Screw not tighten. ASSEMBLYASSEMBLYASSEMBLYASSEMBLY3. Turn spreader upright. For ease of assembly, make sure ON/OFF cable is on top of handle braces. With DOT on the handle assembly facing as shown, secure clamp bracket using a #10 x 3/4 slotted sheet metal screw. Install end of handle assembly between handle braces and secure with (2) 1/4-20 x 1 1/2” hex bolts and nuts. 2. Slide wheels onto end of axle with the hub facing toward frame. Wheels are identical to ease assembly. Align the hole in the wheel hub and the hole in the axle as shown. Secure drive wheel to axle with 3/16 dia. x 2” cotter pin. Insert 1/8 dia. x 1 1/4” cotter pin in the hole near the end of axle to retain free turning wheel. DOT RH. Handle Brace LH. Handle Brace 1/4-20 x 2 1/4” Hex Bolt 1/4-20 Hex Nut Drive Wheel Free Turning Wheel 3/16 Dia x 2” Cotter Pin 1/8 Dia x 1 1/4” Cotter Pin 2 1/4-20 Hex Nut 1/4-20 x 1 1/2” Hex Bolt Handle Assembly ON/OFF Cable Clamp Bracket #10 x 3/4 Sheet Metal Screw ON/OFF Control #10 x 3/4” Sheet Metal Screws Handle Grip #10 x 3/4” Sheet Metal Screws Handle Grip 5. Secure On/Off cable to the clamp bracket using the cable clamp and #10-24 x 5/8” screw and locknut as shown but do not tighten. Place On/ Off control in the “ON” position and set the rate retting dial to the “WASH” position. Pull cable away from hopper sliding it in the cable clamp until the shut off plate stops against the rate setting dial. Tighten cable clamp securely. To check spreader for complete shutoff, pull the On/Off control lever back to the “OFF” position. Check to make sure hole in the hopper is completely closed. If not, loosen the cable clamp and slide the cable forward until the hole in hopper is closed. Re-tighten bolt and check shutoff. Screen Screen Clips 3 4. Attach ON/OFF control to the upper handle using (2) #10 x 3/4” slotted sheet metal screws. Slide handle grips onto the handle cross tube. Soapy water will ease installation. (Do not use petroleum based products). ON ON/OFF Cable Clamp Bracket Clamp Shut Off #10-24 x 5/8” Screw & Locknut Rate Setting Dial Plate 6. Insert screen into hopper by sliding it under the screen clips. O OOOO P PPPP E EEEE R RRRR A AAAA T TTTT I IIII O OOOO N NNNN 1. Check the product package for the rate setting, and recommended swath width. Turn the spreader off by pulling the lever to the “OFF” position as shown. 3. Always fill the spreader on the driveway or sidewalk-not on the lawn. Make sure spreader is in the “OFF” position. Empty after each use. 4. Start spreader moving, then open spreader by moving the lever to the “ON” position. Always push spreader, never pull. Pull the lever to the “OFF position to close spreader. 5. Hold handle so top of spreader is level. Tipping the spreader too far can cause uneven spreading. 6. The settings and swath widths on the product label are recommended starting points. Always check the delivery rate and pattern on a small area before treating a large area. Actual delivery rate can vary due to weather conditions, operating variables, and condition of the product being applied. See “HOW TO DETERMINE SPREADER SETTING AND SWATH WIDTH” for details. 7. Push spreader 2 1/2 m.p.h. (18 feet in 5 seconds) for full 8’ to 14’ spread pattern when applying fertilizer products. Apply header strips at each end of area to be treated then space trips across the area as shown. 2. The rate setting is adjusted by rotating the rate cam to the desired setting. The rate cam locks at each setting. 4 8. Empty spreader after each use. Return leftover material to its original container. SPREAD SWATH APPROX. 8 to 14 FEET ON CENTER OFF H HHHH O OOOO W WWWW T TTTT O OOOO D DDDD E EEEE T TTTT E EEEE R RRRR M MMMM I IIII N NNNN E EEEE S SSSS P PPPP R RRRR E EEEE A AAAA D DDDD E EEEE R RRRR S SSSS E EEEE T TTTT T TTTT I IIII N NNNN G GGGG S SSSS A AAAA N N...
Эта инструкция также подходит к моделям:Газонокосилки - 966043502 (2.12 mb)