INSTALLATION INSTRUCTIONS FOR DECORATIVE ARCH SCREEN PANEL KIT FOR USE WITH LMDV-35/40/45, MPD-35/40/45, MPD35ST, EDV-35/40/45, EDVST & EBVST GAS FIREPLACES 1 2 6 4 5 INSTALLATION INSTRUCTIONS: 1. Remove Top and Bottom Panels a. Remove the top louvered or radiant panel/hood assembly by pulling the assembly up and out (see Figure 2). In instances where the radiant panel is used and it is framed in with tile or other approved material, the hood must still be removed by firmly pulling it forward un

USE ON ANY OTHER FIREPLACE OR APPLIANCE MAY CONSTITUTE A POTENTIAL FIRE HAZARD. • Avoid building extremely large fires as the tempered glass could become damaged. • Use fireplace tools carefully to avoid striking the glass. • Keep wire mesh screens closed during fireplace use. • The fireplace flue damper must remain open until fire is completely out. • Assure wood and embers are well within the confines of the grate area and well away from the glass doors. • Keep glass doors closed at night when

See Figure 4. Figure 4 -GLASS DOOR ADJUSTMENT Top Flange on Glass Door Bottom Vee-fl ange Glass Door Glass Door Latch Glass Door Firebox Floor Some models will have a modesty panel in the control compartment (in front of the valve). The appearance will vary from the example shown below. Modesty Panel 3. Install Firebox Bottom Cover Panel -For Models EDV-35/40/45, see Figure 5a. For Model EDVST see Figure 5b. ScrewStep 1 - Remove 2 fire- box bottom screws. Step 2 - Install the Firebox Bottom Cove

Figure 6 - INSTALL DOORFRAME Left Corner Post Right Corner Post Doorframe 6. Place the doorframe bracket in the locked position as shown in Figure 7. Adjust Doorframe Bracket Doorframe Bracket Locate the doorframe bracket on the lower front of the doorframe and lock it behind the cabinet bottom fl ange as shown here. Figure 7 7. Remove the screen doors from packaging. Install them by aligning hinge pins on the doors with the hinge holes on the doorframe and slide down (see instructions in Figure

See Figure 4. Note: The bottom of the doorframe should be held slightly away as shown in Figure 4. Swing the bottom of the doorframe inward aligning the sides of the doorframe between the glass door and fireplace chassis and tabs on doorframe aligning into slots on fireplace. Swing the bottom of the doorframe in, then push down to ensure engagement. 4. Ensure that the latch(es) below the door are engaged with the door’s veefl ange and fully closed before operating the fi replace (see Figure 3).

• Avoid building extremely large fires as the tempered glass could become damaged. • Use fireplace tools carefully to avoid striking the glass. • Keep wire mesh screens closed during fireplace use. • The fireplace flue damper must remain open until fire is completely out. • Assure wood and embers are well within the confines of the grate area and well away from the glass doors. • Keep glass doors closed at night when retiring to minimize the loss of heated room air up the vent. IMPORTANT: THE FI

Ensure the glass door assembly on the fireplace is properly aligned as follows: a. Open or remove lower compartment door (refer to Homeowner’s Manual provided with appliance). Note: Units with Modesty Panels - Remove the modesty panel as follows: Lift the modesty panel by the tab on the panel’s right end, pull the right end of the panel away from cabinet and then pull the panel diagonally out of the corner post slots on the left side of the unit. Remove the modesty panel carefully, so that none

The chime and pushbutton must be set to the same house security code for the combination to operate together. Note: The push button has 3 additional jumpers that are used to set the chime tune that will play. The chime tune jumpers do not affect the house security code. 1. Remove power or batteries from the chime. 2. To remove the batteries from the pushbutton, open the pushbutton case as shown below. 3. Locate the House Security Code door and screw located on the back of the AC Chime. Remove th

Consult your local distributor for fi replace code information. NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. 1110 West Taft Avenue • Orange, CA 92865 Figure 5 - COMPLETED INSTALLATION Swing the bottom of the doorframe inward, then push into place Figure 4 - INSTALL DOORFRAME 3. Remove the arched screen doorframe from packaging, then install it as follows: a. Locate slots on each side of fi replace. b. Position the top of the doorframe above the top of the glass door assembly (centered and ap

Screen Face [Complete] (A) 2 ea. Upper Brackets w/Screws (B) 2 ea. 1/4”-20 Lower Face Mounting Screws (C) 6 ea. #10 Washers 6 ea. 10-24 Hex Nuts 1 ea. Instruction Sheet Cat. No. Model Description 75382 SCREENF-30 Screen Face, Double Door, Black Figure 1 - Kit Contents TOOLS NEEDED: Phillips Head Screwdriver 3/8” Socket or Nut Driver 5/32” Allen Wrench or T-Handle Wrench GENERAL iNFORMATiON If you encounter any problems, need clarification of these instructions or are not qualified to p