Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
The batteries can explode in a fire. A small leakage of liquid from the battery cells may occur under extreme usage, charging or temperature conditions. This does not indicate a failure. However, if the outer seal is broken and this leakage gets on your skin - a.Wash quickly with soap and water. b. Neutralize with a mild acid such as lemon juice or vinegar. c. If the battery liquid gets in your eyes, flush them with clean water for a minimum of 10 minutes and seek immediate medical attention. (Medical Note: The liquid is a 25-35% solution of potassium hydroxide.) 17. The charger is designed to operate on standard household electrical power (120 volts AC only). Do not attempt to use it on any other voltage! 18. Do not attempt to open the drill housing. 19. UNPLUG CHARGER WHEN NOT IN USE. Table 1 RECOMMENDED MINIMUM AWG* SIZE FOR EXTENSION CORDS FOR BATTERY CHARGERS YOUR CHARGER'S INPUT RATING IS LESS THAN 2 AMPERES. AC Inout Ratina Amperes AWG* Size of Cord Equal to or But less Length of Cord, Feet greater than than 25 50 100 150 , 0 2 18 18 18 16 ‘American Wire Gauge 5 Bubble Level Your drill is equipped with a bubble level that assists you in drilling level holes. For horizontal drilling, tilt the drill up or down as required so that the bubble floats in the center of the parallel lines drawn on the glass.When the bubble is centered between the lines, as shown in Figure 1, the drill is level. For vertical drilling, align the drill so that the bubble floats in the center of the bull's eye, as shown in Figure 2. To assure accuracy, first place a level on your workpiece and position the piece so that it's level. Then, when the drill reads level, the two will be aligned. (Any level can only indicate level with respect to the earth's gravitational field.) NOTE: The level is filled with mineral oil that may cause minor skin or eye irritation when contacted. If the level breaks and the fluid gets on your skin, rinse thoroughly with water. If the liquid gets in your eyes, rinse thoroughly with water and contact a physician immediately. BUBBLE- CHARGING SOCKET- SCREWDRIVER BIT RELEASE BUTTON Bit Storage A double ended (#2 Phillips and Straight) screwdriver bit is included with ' your drill. The bit stores in the drill handle, as shown in Figure 3. To remove the bit from the handle, hold the drill normally and depress the button shown in Figure 3. The bit will drop out of the handle. To reinstall into handle, simply push it into the hole as far as it will go. (You may have to twist it slightly in order for it to go all the way in.) BUBBLE LEVEL TRIGGER SWITCH CHARGE INDICATOR CHUCK KEY Trigger Switch and Control Lever To turn the drill "ON" squeeze the trigger switch shown in Figures 4. To turn the tool "OFF", release the trigger switch. TWO SPEED SWITCH The drill has a two speed switch that produces either 300 RPM or 600 RPM. Squeezing the switch just far enough so that the tool runs yields 300 RPM. Squeezing a little farther until you hear the drill speed up produces 600 RPM. NOTE: There is a slight pause between the two speeds. Keep squeezing the trigger and the drill will start again. The two position Control Lever switches the drill from Forward for drilling holes and driving screws to Reverse for backing out broken drill bits and removing screws. To run the drill in Forward, pull the Control Lever forward toward the chuck, as shown in Figure 4. To run the drill in Reverse, push the lever back toward the trigger switch. Chuck & Key Turn Chuck collar to open Chuck jaws. Place bit in Chuck as far as it will go. Tighten Chuck collar by hand. Place Chuck Key in each of the three holes, and tighten in clockwise direction (Figure 5). It's important to tighten Chuck with all three holes to prevent slippage. To release bit, turn the Chuck Key counterclockwise in just one hole, then loosen Chuck by hand. ' When not in use, the Chuck Key Can be stored in the tool. To remove the Key, place thumb as shown in Figure 5 and push key firmly downward out to its holding clip. To replace Key, push firmly and completely up into the socket. (Figure 7.) Charging the Drill Before attempting to charge your drill, thoroughly read ALL of the safety instructions. To charge your drill, follow the steps below. 1. Remove any accessories from the chuck and plug the output cord of the charger into the socket in the front of the drill handle. 2. Plug the charger into any standard 120 volt electrical outlet. 3. Allow the tool to remain in this condition for three hours. 4. Unplug the charger from the power supply, then unplug the tool from the charger. Charge Indicator Your drill is equipped with a charge indicator light that comes on whenever the drill is charging. The light remains lit whether the drill is fully charged or not and goes out when the tool is taken off charge. The light is located on the side of the handle near the charging socket. Important Charging Notes 1. After normal us...