You will hear a click as the clips engage. 3. Fully push the drawer into the case. Global Machinery Company 16 Scammel Street, Campbellfield Victoria, Australia 3061 Tel: (03) 9303 2133 Fax: (03) 9308 7822 Customer Helpline 1300 880 001 (Australia) 0800 445 721 (New Zealand) 300PCE 030117 300PCE EDS

This is ideal for demolition work 4. Stop rotation (non powered) with hammer action and the accessory bit is fixed from rotating. This is ideal for lifting tiles. CARBO gBREo a Also featuring carbon Fibre and Magnesium construction for the ultimate in strength, durability and reduced tool weight. The body also features Brush Show for easy access to the brushes for easy replacement. A safety clutch mechanism provides an increased level safety to the operator should the accessory become jamm

All persons who use and service the machine have to be acquainted with this Manual and must be informed about its potential hazards. Children and infirm people must not use this tool. Children should be supervised at all times if they are in the area in which the tool is being used. It is also imperative that you observe the accident prevention regulations in force in your area. The same applies for general rules of occupational health and safety. The manufacturer shall not be liable for any cha

With one hammer (Rocking Dog) impact mechanism and useful accessories, this kit is used as a general purpose tool kit by DIYers and hobbyists. 1. This impact wrench is a part of a high pressure system. Do not exceed maximum operating pressure of the air tool (90PSI). The impact wrench could explore and may result in death or serious injury. 2. Disconnect the impact wrench from air compressor before changing tools or accessories, servicing and during non-operation. 3. Always wear safety glasses a

to the tool. • Never carry the tool by the hose. • Avoid unintentional starting. Don’t carry an air tool which is connected to an air hose, with your finger on the trigger. • Repair servicing should be done only by an authorized service representative. • Air tools can cause the workpiece to move upon contact leading to injury. • Use clamps or other devices to prevent movement. Risk to injury (cont.) • Loss of control of the tool can lead to injury to self or others. • Never operate tool while un

There are 3 levels of charge low, medium and high. When the battery indicator is showing only 1 LED (low) the battery should be removed and put on the charger. LED Work area light The drill has 3 LED lights (11) to illuminate the work area and improve vision when drilling in areas with insufficient light. To turn the LED lights on and off depress the LED light switch (13). Using the drill Use the forward/reverse switch (4) to select the direction of rotation, then pull the trigger (3). This trig

Do not allow any liquid to come into contact with the charger. There is a danger of electric shock. • To allow the battery pack to cool down after charging, do not place it in a hot environment such as a metal shed or open trailer left in the sun. • The charger is not intended for any use other than charging the exact type of rechargeable battery pack as supplied with the charger.Any other use may result in the risk of fire, electric shock or electrocution. • The charger and battery packs suppli

Damaged or entangled cords increase the risk of electric shock. • When operating a power tool outdoors, use an outdoor extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. GTX12100K GTX144100K 443T 183T 243T Nominal battery voltage 12V 14.4V 18V 24V Charger 230–240V ~ 50Hz, 1.2A 230–240V ~ 50Hz, 1.2A 2230–240V ~ 50Hz, 1.2A 230–240V ~ 50Hz, 1.2A Charging time 3-5 Hours 3-5 Hours 3-5 Hours 3-5 Hours Drill no load speed 0–550min-1 0–550

Do not leave a battery charging for longer than 24 hours. 1. Align and slide the slim line adaptor (9) onto the battery until the battery pack latches “click” into position. Check the adaptor is flush with the battery and there is a firm connection. 2. Connect the power supply from the charger to the slim line adaptor via the socket in the rear of the adaptor housing. 3. Plug in the charger and switch on. The red LED indicator will show power to the adaptor and that charging is taking place. 4.