Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Second, install the camera at the desired location and run Cat 5 wire from the camera to the channel location. Third, apply power and select an unused channel for the CatCam picture to appear on all the televisions. WARRANTY Multiplex Technology, Inc. warrants this defects in materials and the date of purchase or or at its option, replace defective product. To obtain warranty service, material authorization (RMA) to Multiplex Technology, Inc., 3001 Enterprise Street, Brea, 92821, Attention: Customer Service. Please the outside of the carton. Any implied warranty arising from the sale implied warranties of merchantability and fitness to the warranty stated above. MTI shall not losses or damages or expenses, whether direct, incidental arising from the use of or the inability to use Some states do not allow limitations on how long the implied lasts or the exclusions or limitations or incidental or damages, so the above limitations and exclusions may apply to you. This warranty gives you specific legal rights, and may have other rights which may vary from state to state. Specifications: 5° C 9511 (B&W) 9511PAL(AUS) 9521 (Color) HHR/BID HHR/BID lens viewing angle resolution: horizontal 525 lines vertical 350 lines standard lens cover: minimum light level 2 lux video input format EIA 78° 525 lines 350 lines smoked 2 lux CCIR 525 lines 350 lines 8 lux NTSC input signal 1.0 V peak-to-peak @ 75. signal-to-noise ratio >45 dB white balance automatic electronic shutter speed automatic: 1/60 to 1/50,000 second tuning range UHF 14 to 64 CATV 65 to 125A 21 to 62(28 to 67) 14 to 64 65 to 125A power supply included with product mains power 105 to 125 210 to 250 105 to 125 output of power supply 15VDC 600mA general injector module camera module width x height x depth 6.5” x 3.5” x 1.25” 2.75” x 4.5” x 3” (16.3cm x 9cm x 3.2cm) (6.9 cm x 11.4cm x 7.6cm) shipping weight 2 lbs (0.9 kg) operating temperature –4°F to 131°F (–20°C to 55°C) A excluding channels 95 through 99 Installation: Locate the incoming or antenna (Usually found on the Remove the lock screw injector and slide the Use the mounting holes affix the channel injector Mount the injector within Use mounting 4” of the splitter holes on the bottom plate to attach channel injector to the wall © 1999 Disconnect the incoming CATV or antenna feed from the existing splitter and attach it to the channel injector as shown. Before Out to TVs Incoming CATV or antenna coax Now attach the supplied coax jumper back to the existing splitter and tighten all connections with a 7/16” wrench. After Mount the injector within 4” of the splitter Supplied coax jumper goes back to splitter Out Incoming CATV or to TVs antenna coax © 1999 Installation The camera wire from the shown. prepare the Cat 5 wires stripping 1” of outer sheath and 1/8” of insulation insert the 6-32 screws into frame and bottom holes of gang box gasketframe Attach Cat 5 wire to camera following color coding. note: When using quad wire connect wires only to p...
Эта инструкция также подходит к моделям:Домашние кинотеатры - CAT CAM 9511BID B&W (144.25 kb)
Домашние кинотеатры - CAT CAM 9511PAL B&W (144.25 kb)
Домашние кинотеатры - CAT CAM 9521BID COLOR (144.25 kb)
Домашние кинотеатры - CAT CAM 9511HHR B&W (144.25 kb)