Оценок - 3, средний балл: 5
(
)
)
|
Фрагмент инструкции
Before Out to TVs Incoming CATV or antenna coax Now attach the supplied coax jumper back to the existing splitter and tighten all connections with a 7/16” wrench. After Mount the injector within 4” of the splitter Supplied coax jumper goes back to splitter Out Incoming CATV or to TVs antenna coax © 1999 Installation The camera wire from the shown. prepare the Cat 5 wires stripping 1” of outer sheath and 1/8” of insulation insert the 6-32 screws into frame and bottom holes of gang box gasketframe Attach Cat 5 wire to camera following color coding. note: When using quad wire connect wires only to pins 1, 2, 5 and 6. Leave the resistor in place at pins 3 and 4. 4 note: When using Cat 5 wire remove the default resistor that is in pins 3 and 4 of the camera pin 1 2 3 4 5 6 7 8 Default resistor Green pin 1 Red 2 Black 5 Yellow 6 Bl/W Blue Org/W Orange Gr/W Green Br/W Brown Programming Valid channels Channels 95-99 Channel Spacing: Skip at least one number existing UHF/CATV channel. (example 14 and 16: OK 14 and 15: Unacceptable) Error Indication: If an error occurs or an incorrect channel flash quickly for one second and return Cable HRC and IRC considerations: Most cable services use IRC frequency assignments. default for the 9500 series. However, if the cable services uses HRC or the TV appears to search for the “created channel”, channel injector for HRC. For HRC enter 98. Reset to IRC by entering 99. Entries 98 and 99 are for setting HRC or IRC only. They will not change the channel number. With programming complete, test each TV in the system to see that it is receiving the new channel. How to Determine which source on and one unused channel avoid interference. channels and appear © 1999 Upper right corner onchannel injector green LED programming button To program: For example channel 60 1: Press the button 6 times. 2: Wait for the LED to relight. 3: Press the button 10 more times (pressing 10 times enters “0”). The injector will now combine the camera feed on channel 60 with existing channels from the incoming CATV or antenna. To program a three digit channel: For example channel 120 1: Press the button 1 time. 2: Wait for the LED to relight. 3: Press the button 2 more times. 4: Wait for the LED to relight. 5: Press the button 10 more times. Finding Unused Channels CATV: Determine the highest channel number delivering a picture, excluding 95-99. Tune the TV up one channel at a time from the last channel with a picture until finding one channel with no trace of a picture or interference, just snow. Antenna: Tune the TV one channel at a time from channel 14-64. Locate one channel that has no trace of a picture or interference, just snow. Channel At the channel connect Cat color coding on blue/white pin 1 © 1999 When using only quad wire use positions 1, 2, 5 and 6 and follow color coding. green pin 1 run the Cat 5 wire through the grommet at the bottom of the injector Applying Power and Programming Step Three The 9500 series has three different met...
Эта инструкция также подходит к моделям:Домашние кинотеатры - CAT CAM 9511BID B&W (144.25 kb)
Домашние кинотеатры - CAT CAM 9521BID COLOR (144.25 kb)
Домашние кинотеатры - CAT CAM 9521HHR COLOR (144.25 kb)
Домашние кинотеатры - CAT CAM 9511HHR B&W (144.25 kb)