Also, the protective sheet may be replaced in the CD-ROM pack to provide protection when the unit is moved or if it will not be used for an extended period of time. • Do not place items other than CDs on the tray. • Do not leave the tray in the open position or touch the lens area. Should the lens become soiled by dust or dirt, the unit may not read CDs properly. • Do not apply excessive force to the tray in the open position, doing so could damage the tray. • Do not open the CD-ROM drive or

^ Deactivate unnecessary equipment using in Setup Utility. 2m Removing the device (Floppy disk drive) ® Press the MP release button. The device will eject slightly. (2) Remove the device by holding both sides of the device. • Please handle the device as shown (holding both sides). Otherwise, the device may be damaged. Also, do not apply excessive downward force on the device. The projections at the bottom of a device become deformed. • Be sure the shape of the lock at the bottom of a devic

(Deleting “rem” causes the item to become valid.) DEVICEHIGH=C:\WINDOWS\COMMAND\OAKCDROM.SYS /D:MSCD000 (If this line is missing, add it.) 5 Press( Alt) +CD 1 thenfSP to save the file. Then press C Alt) +C~F"). then to exit the Edit program. 6 Follow the same steps to edit the “AUTOEXEC.BAT” file, edit autoexec.bat ( Enter ) 7 Move the cursor to the line containing “MSCDEX.EXE” and delete the characters “rem” at the beginning of the line. (Deleting “rem’’ causes the item to become valid.) LO

For information on how to install the software, refer to the included “Easy CD Creator™4/DirectCD™3”. • Be sure to use discs conforming to the proper write speeds. CD-R write speed 300 KB/s (2x speed) 600 KB/s (4x speed) 1200 KB/s (8x speed) CD-RW write speed 300 KB/s (2x speed) 600 KB/s (4x speed) • This CD-R/RW Drive Pack cannot write to High-Speed CD-RW discs. • If the write operation is to involve a long period of time, be sure to connect the AC adaptor. If the battery power runs low an

Wipe this moisture off with a soft, dry, lint-free cloth before using the disc. • Do not drop, bend, or place heavy objects on top of discs. • Cleaning the disc using a CD cleaner is recommended once every 2 or 3 months. After wiping the disc with a moist, soft cloth, wipe it with a dry cloth. Always wipe from the center toward the edge. Using the Drive Installing/Removing a Drive Refer to the Reference Manual included with your computer on how to install/remove the drive. c ©mTioN Be s

Deactivate unnecessary equipment using in Setup Utility. Software Preparation (first time only) The following settings are necessary to prepare the DVD-ROM Drive Pack for use: 4WiñclowslÑ¡T¡i : The following settings are unnecessary.) 1 Add the check mark for [DMA] in [Start] - [Settings] - [Control Panel] - [System] - [Device Manager] - [CD-ROM] - [MATSHITA DVD-ROM SR-8173] - [Settings], 2 Set [L:] for both [Start drive letter] and [End drive letter] in [Reserved drive letters], then pres

Deactivate unnecessary equipment using in Setup Utility. A PC Card is required to play DVD-Video or MPEG2 files when using CF-27 model. Separate application software is required to play DVD-Video or MPEG2 files when using CF-28 model. The picture quality of a DVD depends on the DVD playback software. Refer to the manual of separate DVD playback software. ¡-Power-saving-Mode^ If the DVD-ROM Drive Pack has not been accessed within 90 seconds, the drive motor will automatically shut down to re

DURCI I FIJI IRl .’NC. ANDERER VORGÄNGE ALS DER HIER ANGEGEBENEN KANN ZU GEFÄHRLICHER SIR AI II.UNG FÜHREN. REPARATUREN DÜRFEN NUR VON QUALIFIZIERTEM FACHPERSONAL Dl JRCI «GEFÜHRT WURDEN. AVERTISSEMENT! CEF APPARFII. IJTD ÎSE UN LASER. L’UTILISATION DE COMMANDES OU DE RÉGLAGES OU L'EXÉCUTION DE PROCÉDURES AUTRES QUE CELLES SPÉCIFIÉES ICI PEUVENT PROVOQUER UNE EXPOSITION À DES RADIATIONS DANGEREUSES. NE PAS OUVRIR LES COUVERCLES NI ESSAYER DE RÉPARER SOI-MÊME. CONFIER TOUT TRAVAIL D'ENTRETIEN

MS-DOS® and Windows® arc registered trademarks of Microsoft Corporation in the United States and/or other countries. Usage Precautions • Do noi place items other than discs on the tray. • Do not leave the tray in the open position or touch the lens area. Should the lens become soiled by dust or dirt, the unit may not read discs properly. • Under some conditions, dust may build up on the optical lens or disc, possibly resulting in malfunction. • Do not apply excessive force to the tray in th

Wipe this moisture off with a soft, dry, lint-free cloth before using the disc. • Do not drop, bend, or place heavy objects on top of discs. • Cleaning the disc using a CD cleaner is recommended once every 2 or 3 months. tray. pears. O X After wiping the disc with a moist, soft cloth, wipe it with a dry cloth. Always wipe from the center toward the edge. Software Preparation (first time only) &Wjn9ô^95|ItWjrT9ô^98ÿ Confirm the following contents in [Start] - [Settings] - [Control Panel