(Deleting “rem” causes the item to become valid.) DEVICEHIGH=C:\WINDOWS\COMMAND\OAKCDROM.SYS /D:MSCD000 (If this line is missing, add it.) 5 Press( Alt) +CD 1 thenfSP to save the file. Then press C Alt) +C~F"). then to exit the Edit program. 6 Follow the same steps to edit the “AUTOEXEC.BAT” file, edit autoexec.bat ( Enter ) 7 Move the cursor to the line containing “MSCDEX.EXE” and delete the characters “rem” at the beginning of the line. (Deleting “rem’’ causes the item to become valid.) LOADH1GH C:\WINDOWS\COMMAND\MSCDEX.EXE /D:MSCD000 /L:L (If this line is missing, add it.) 8 Press fAlD +CE) , then (D to save the file. Then press CaID +CE) , then to exit the Edit program. 9 Restart the computer. Writing to CD-R/RW Discs Set the included CD-ROM “Easy CD Creator™ 4/DirectCD™ 3” in the CD-R/RW drive and install the application software on your computer. For more detailed information, refer to the “Easy CD Creator™ 4/DirectCD™ 3”. Setting a Disc 7 Open the disc tray Press the eject button and slowly pull out the tray 2 Place a disc Place the disc with the label facing upward in the drive and push down until the center holder clicks Place a finger on the center holder and lift up on the edge of the disc 3 Close the disc tray ' Close the tray without touching the eject button Label side up Center Holder Eject Button • Do not apply excessive force to the tray in the open position, doing so could damage the tray • cUsing PC Cards> If the PC Card does not work, there may be no interrupt request (IRQ) line available Deactivate unnecessary equipment using in the Setup Utility Xnote)- • References to “CD/DVD” in the Setup Utility will not change when the CD-R/RW Drive Pack is installed • If the vibration of the CD-R/RW drive is excessively high set ICD/DVD Drive Speed] in the Setup Utility to [Low] Information for the CD-R/RW Drive Using the included CD-ROM "Easy CD Creator™ 4/DirectCD™ 3", install the application software on your computer with the following procedure. • If you are using CD-R or CD-RW discs, read the descriptions written on the packages of the discs. • CD-RW discs cannot be read with a drive* unable to accommodate CD-RW discs. * Consult with the manufacturer of the drive. • Using the included CD-ROM "Easy CD Creator™ 4/DirectCD™ 3”, install the application software on your computer. For information on how to install the software, refer to the included “Easy CD Creator™ 4/DirectCD™ 3”. • Be sure to use discs conforming to the proper write speeds. CD-R write speed 300 KB/s (2x speed) 600 KB/s (4x speed) 1200 KB/s (8x speed) CD-RW write speed 300 KB/s (2x speed) 600 KB/s (4x speed) • This CD-R/RW Drive Pack cannot write to High-Speed CD-RW discs. • If the write operation is to involve a long period of time, be sure to connect the AC adaptor. If the battery power runs low and the power of the computer is cut, the write operation may end in failure. • Depending on the disc, the quality of the write operation may not be so good. We recommend using any of the following discs. Recommended Discs: • TAIYOYUDEN Co., Ltd. • MITSUI CHEMICALS, Inc. • RICOH Co., Ltd. • MITSUBISHI CHEMICAL Co., Ltd. • TDK Co., Ltd. • HITACHI MAXELL, Ltd. • FUJI PHOTO FILM Co., Ltd. • RICOH Co., Ltd. • MITSUBISHI CHEMICAL Co., Ltd. Troubleshooting The computer does not recognize the CD-R/RW Drive Pack. • Check the settings by following the instructions in “Software Preparation”. • Is the CD-R/RW Drive Pack properly mounted in the multimedia pocket? The MP indicator ([M^) does not light. Is the disc loaded on the tray correctly? Cannot play disc or read data from it. Is the disc bent, scratched, or dirty? Cannot eject disc. Is the computer powered on? To remove a disc when the computer is powered off, insert a sharp object such as the bent-out tip of a paper clip into the emergency hole. Pushing it completely to the end will free the tray so that it can be pulled out. Emergency Hole A blue background appears on the screen with the MPEG image. Did you open the CD-R/RW drive or remove the MPEG disc while it was operating? Re-insert the MPEG disc and close the CD-R/ RW drive. Press ( Enter). The disc tray does not close. Did you touch the eject button when you close the tray? The computer hangs or reboots. • Is an external CD-ROM drive or DVD-ROM drive connected? When the CD-R/RW Drive Pack is installed, do not use an external CD-ROM drive or DVD-ROM drive. • Was the computer turned off before the installation/removal of the CD-R/RW Drive Pack? The computer needs to be off so that the CD-R/RW Drive Pack can properly initialize during W'indows startup. 10 Specifications Item Description Operating voltage range DC 5 V ± 0.25 V CD-ROM read 3600 KB/s 24x speed (Max.)*1 Data transfer rate CD-R write 300 KB/s 2x speed 600 KB/s 4x speed 1200 KB/s 8x speed CD-RW write 300 KB/s 2x speed 600 KB/s...
)
