Оценок - 4, средний балл: 4.3 ( )

Производитель: Panasonic Размер: 1.1 mb Название файла: CFVDD721M.PDF Язык инструкции:

Wipe this moisture off with a soft, dry, lint-free cloth before using the disc. • Do not drop, bend, or place heavy objects on top of discs. • Cleaning the disc using a CD cleaner is recommended once every 2 or 3 months. tray. pears. O X After wiping the disc with a moist, soft cloth, wipe it with a dry cloth. Always wipe from the center toward the edge. Software Preparation (first time only) &Wjn9ô^95|ItWjrT9ô^98ÿ Confirm the following contents in [Start] - [Settings] - [Control Panel] - [System] - [Device Manager] - [CD-ROM] - [MATSHITA DVD-ROM SR-**** ] - [Settings]. Make the settings if they have not yet been made. • Add a check mark for [DMA]. • Set both [Start drive letter] and [End drive letter] in [Reserved drive letters] to [L:]. Xnote)-> When using CF-71 series • {(with the F1RSTAID CD included): When reinstalling, refer to the above to set the reserved drive letters of the DVD-ROM drive. • When booting up from the FIRSTAID FD (for example, to reinstall the operating system), the DVD-ROM Drive does not have to be replaced by the CD-ROM Drive (CF-VCD711). The CD-ROM driver will recognize the DVD-ROM Drive. Min3c^F2Q00jj] Confirm that [Transfer Mode] is set to [DMA if available] in [Control Panel] - [System] -[Hardware] - [Device Manager] - [IDE ATA/ATAPI controllers] - [Secondary IDE Channel] - [Advanced Settings] - [Device 0]. Perform this setting if it has not yet been made. Using the DVD-ROM Drive Pack in the MS-DOS Mode To use the DVD-ROM Drive Pack in the MS-DOS mode, configure the drive following the steps below after performing the above preparations. If the steps listed below are performed without completing above preparations first, the drive will not operate prop* erly. 1 Click the [Start] button then select [Shut Down], 4L Select [Restart in MS-DOS mode] and click [OK]. 3 Open the “CONFIG.SYS” file for editing by issuing the following commands: cd\C Enter) edit config.sys ( Enter ) 4 Move the cursor to the line containing “ C OAKCDROM.SYS*” and delete the characters “rem” at the beginning of the line. (Deleting “rem” causes the item to become valid.) DEV1CEHIGH=C:\WINDOWS\COMMAND\OAKCDROM.SYS*/D:MSCDOOO (If this line is missing, add it.) * (KH1): ATAP1CD.SYS 5 Press C Ait) +CF) , then C S ) to save the file. Then press C Alt 3 + ( F ). then CD to exit the Edit program. 6 Follow the same steps to edit the “AUTOEXEC.BAT” file, edit autoexec.bat C Enter ) 7 Move the cursor to the line containing “MSCDEX.EXE” and delete the characters “rem” at the beginning of the line. (Deleting “rem” causes the item to become valid.) LOADHIGH C:\WINDOWS\COMMANDVMSCDEX.EXE /D:MSCD000 /L:L (If this line is missing, add it.) Q Press ( Alt ) + CD , then © to save the file. Then press CM) +CD , then to exit the Edit program. 9 Restart the computer. Power-saving Mode If the DVD-ROM Drive Pack has not been accessed within 90 seconds, the drive motor will automatically shut down to reduce the power consumption. When the DVD-ROM Drive Pack is accessed once again, the power of the drive motor is turned on. However, approximately 30 seconds are required until data is actually read from the disc. Setting a Disc 7 Open the disc tray Press the eject button and slowly pull out the tray. 2 Place a disc Place the disc with the label facing upward in the drive and push down until the center holder clicks. Place a finger on the center holder and lift up on the edge of the disc. 3 Close the disc tray Close the tray without touching the eject button. Label side up Center Holder Eject Button (This illustration features CF-72 series.) - ----------------- -------^ • Do not apply excessive force to the tray in the open position, doing so could damage the tray. I • If the PC Card does not work, there may be no interrupt request (IRQ) line available. Deactivate unnecessary equipment using in the Setup Utility. Xnote)---v • References to “CD-ROM” in the Setup Utility will not change when the DVD-ROM Drive Pack is installed. • If the vibration of the DVD-ROM drive is excessively high, use the Setup Utility to reduce the CD-ROM or DVD-ROM drive speed (by setting it to [Low] or [12x speed])*. * This setting does not work for the DVD-ROM disc when this drive is used with the CF-71 series. V_J Troubleshooting The computer does not recognize the DVD-ROM Drive Pack. • Check the settings by following the instructions in “Software Preparation”. • Is the DVD-ROM Drive Pack properly mounted in the multimedia pocket? The MP indicator ([M^) does not light. Is the disc loaded on the tray correctly? Cannot play disc or read data from it. Is the disc bent, scratched, or dirty? Cannot eject disc. Is the computer powered on? To remove a disc when the computer is powered off, insert a sharp object such as the bent-out tip of a paper clip into the emergency hole. Pushing it completely to the end will free the tray so that it can be pulled out. Emergency Hol...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: