Оценок - 2, средний балл: 4 ( )

Производитель: Samsung Размер: 7.2 mb Название файла: Язык инструкции:

• Locate the nearest cold drinking water line. • Follow the instructions in the water filter installation kit. • After connecting the water supply line to the Cartridge Holder inlet and installing the Filter Cartridge (insert plastic line in fully). • Turn on water supply and flush 3L into a bucket to clear the water filter. • The water filter must be installed outside the refrigerator. It is not provided with your new refrigerator. The filter cartridge (8) and holder (9) kit can be purchased from the retailer where you purchased this refrigerator. • Do not use copper line. • Cut the tubing, making sure the ends are square and clean. Water line fixer and screws Pipe connector Water line Fastner - Refer to ‘MAKING MINOR ADJUSTMENTS BETWEEN DOORS’(on page 24) Incorrect Correct 90 degree 1. C old Water line 2. P ipe Clamp. 3. P lastic line 4. C ompression Nut 5. C ompression Sleeve 6. P acking Nut 7. Shut Off Valve 8. Filter Cartridge 9. C artridge Holder 12_ setting up Connect the water line to the fridge • Connect the plastic line on the back of your fridge to the cartridge holder outlet (fully insert the plastic line to the cartridge holder outlet). • Insert plastic clip to the cartridge holder inlet and outlet. • Turn water on and check for any leakage. • You can purchase the necessary filter cartridge at the retailer where you purchased this refrigerator. Make sure you buy the SAMSUNG filter cartridge (Replacement cartridge No : DA29-10105J) to ensure the best performance. • Water line must be connected to drinkable water only • A compression fitting and nut kit is supplied with the unit and it is inside the fridge drawer. • When pushing the Refrigerator back, make sure you don’t roll over the power cord or water line (Icemaker supply line) To use without the water filter section Connecting to the water supply line • Shut off the main water supply line and turn the Ice maker to the off position. • Locate the nearest cold water drinking line. 1. First, shut off the main water supply line. 2. Locate the nearest cold, drinking water line. 3. Follow the Water line Installation Instructions in the installation kit. The water line must be connected to the cold water pipe. If it is connected to the hot water pipe, it may cause the purifier to malfunction. CAUTION Cartridge Holder Clip Filter cartridge Plastic line (Provided) 1. C old Water line 2. P ipe Clamp. 3. P lastic line 4. C ompression Nut 5. C ompression Sleeve 6. P acking Nut. 7. Shut Off Valve Close Main Water pipe Close Main Water pipe No gap setting up your refrigerator Connecting the water line to the refrigerator 1. Remove the cap from water line on the unit and insert compression nut to the water line on the unit after disassembling from provided water line. 2. Connect both water line from the unit and water line in the kit. 3. Tighten the compression nut onto the compression fitting. There should be no gaps between (A, B & C ) 4. Turn water on and check for any leakage. Remove cap Loosen a Water Line from unit No gap Water Line from unit Only connect the water line to a drinkable water source. If you have to repair or disassemble the water line, cut off 6.5mm of the plastic tubing to make sure you get a snug, leak-free connection. After the water supply has been installed check all the joints to ensure there are no leaks. cAUTION • Samsung Warranty does not cover THE WATER LINE INSTALLATION. • The cost of the water line installation is at the customers expense, unless the retailer has covered this expense in the delivery charge. • Please contact a Plumber or Authorized Installer for the installation if needed. • If Water leakage occurs due to improper installation, Please contact installer. 01 SETTING Up s sse eet ttt tti iin nng u g ug up pp _ __1 113 33 SETTING Up ThE REFRIGERATOR Now that you have your new Refrigerator installed in place, you are ready to set up and enjoy the features and functions of the appliance. By completing the following steps, your Refrigerator should be fully operational. 1. Place the Refrigerator in an appropriate location with reasonable clearance between the wall and the Refrigerator. Refer to installation instructions in this manual. (P8. Selecting the best location for the Refrigerator) 2. Once the Refrigerator is plugged in, make sure the interior light comes on when you open the doors. 3. Set the Temperature control to the coldest temperature and wait for an hour. The Freezer will get slightly chilled and the motor will run smoothly. 4. After powering the Refrigerator, it will take a few hours to reach the appropriate temperature. You can store food and drinks in the Refrigerator after the temperature is sufficiently cool. Required Tools (Not provided) Phillips Head Driver(+) Flat Head Driver(-) Socket Wrench (10mm) (for bolts) Hex Wrench (O5mm) (for Mid hinge) Hex wrench (5/32 inch) (for Mid hinge shaft) REMOvING ThE REFRIGERATOR dOORS Some installations require door/drawer removal to transport the Refrigerator...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: