Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
1. Possible to drop or scratch the door at this time. 2. Middle hinge cap may come off with the door. 7. Disassemble middle hinge cap. 8. Remove 1 screw and 2 bolts of each side (use O5mm allen wrench). 1. At first, Remove left side middle hinge and right side. 2. Be careful not to drop the freezer door. 9. Remove the freezer door by lifting it up. 1. Possible to drop or scratch the door at this time. 2. Low hinge cap may come off with the door. 10. Remove 2 screws. 11. Separate front leg Cover. Cap Cover 20_ setting up 12. Separate the Cap of the front leg Cover. (pull out inside of Cap) 13. Insert the Cap on the other side of the front leg Cover. 14. Remove 2 bolts of each hinge with the 10mm wrench. 15. Place them in front of each side. 16. Separate low hinge shaft by using 5/32” wrench and disassemble low hinge leg by turning it colockwise, and then assemble the low hinge by turning it over. 17. Reattach the former right hinge on the left side and the former left hinge on the right side by using 2bolts. 18. Separate stopper by removing 1 screw on the right lower side of freezer and assemble the stopper on the left side by reversing it. 19. The middle hinge for reversing a door can be found in the fridge. 20. Change the middle hinges assembled at refrigerator to the middle hinges in the fridge with handles. 21. Use the black hinge cap of the middle hinge assembled at refrigerator. Then place it at the bottom of the left middle hinge supplied separately. Use the Flat-blade screwdriver(-). Cap setting up _21 01 setting up setting up your refrigerator 22. Place the hole in the bottom of the freezer door over the low hinge. 23. Replace the middle hinge connected to the freezer. 24. Insert and tighten the screw into the left and right middle hinges with a philips screwdriver(+). Insert and tighten the 2 hex head bolts into the left and right middle hinges with an allen wrench(O5mm). 25. Replace the cap on the middle hinge. 26. Place the hole in the bottom of the left door over the middle hinge. 27. Insert the left upper hinge shaft into the hole on the corner of the fridge door. 28. Insert the upper hinges into the holes at the top of the door. Insert and tighten the 3 hex head bolts into the left and right upper hinges with a socket wrench(10mm). 29. Insert and tighten the ground screw into the left and right upper hinges with a philips screwdriver(+). 30. Connect the electronic wire on the top of the refrigerator. 31. Position the top table in place. Insert and tighten the 3 screws into the top table with a philips screwdriver(+). 22_ setting up insta llation of the handles REF handle installation 1. Make sure the word “UP” on the rear of the handle is facing right side up. 2. a. Match the upper and lower handle Locking Tabs on the doors to the handles. b. Fix the handles to the doors by sliding them down firmly until you hear a click sound. 3. Check the installation of the handles by pulling on them. If the handles have been inserted correctly, they should not move. Ensure the two handles are horizontally aligned. • If the REF handles are not aligned, repeat number 2. To align the doos, refer to the owner’s manual, section ‘Leveling the refrigerator’ FRE handle installation (Drawer-Type) 1. Make sure the word “The Upper Direction” on the side of the handle if facing up. 2. a. Align the handle with the mounting studs. b. Push the handle onto the mounting studs until you hear a click. 3. Check the installation of the handle by pulling on it. If the handle has been inserted correctly, it should not move. • If the Freezer handle is not attached, repeat step 2. • Swing-Type Model does not include FRE handle. setting up your refrigerator AdjUSTING ThE dOORS After putting the doors back on the Refrigerator, make sure the Refrigerator is level so that you can make final adjustments. If the Refrigerator is not level, it will not be possible to get the doors perfectly even. Also it is possible to sweat in the refrigerator and ask more energy bills. For example, when the left side is lower than the right side, insert a flat-blade screwdriver into a notch on the left control lever, and turn it clockwise or counter clockwise to level the door. Turning it clockwise to raise the refrigerator and counterclockwise to lower it. For the left side is higher, do it with right lever. Both control levers must be surely touching the floor to avoid the possible personal injury or WARNING property damage because of tipping. When the left side is higher. Whentheleftsideislower. Screwdriver(-) Screwdriver(-) ControlLeverControlLever 01 SETTING Up s sse eet ttt tti iin nng u g ug up pp _ __23 2323 24_ setting up setting up your refrigerator making minor adjustments between doors Remember, a level Refrigerator is necessary for getting the doors perfectly even. If you need help, review the previous section on leveling the Refrigerator. 1. Pull out the freezer drawer ( 1 ), then you can see the middle hinge ( 2 ) . 2. Insert the supplied...
Эта инструкция также подходит к моделям:Холодильники - RF62NEPN (7.2 mb)
Холодильники - RF62NERS (7.2 mb)
Холодильники - RF62QEPN (7.2 mb)
Холодильники - RF62WBPN (7.2 mb)